HR2S-301N IDEC, HR2S-301N Datasheet - Page 7

• Manufacturer Part Number: HR2S-301N
• Description: 47T1443
• Manufacturer: IDEC

HR2S-332N-T075/T15/T30
Note: Time-delay duration can be set in 15 steps.
Specifications
(110127)
HR2S-332N-T075/T15/T30 Safety Relay Modules
Applicable Standards
Applicable Standards for Use
Performance level (PL)
Safety Category
Stop Category
Operating Temperature
Relative Humidity
Altitude
Insulation Resistance
Dielectric Strength
Shock Resistance
Bump
Vibration Resistance
Degree of Protection
Rated Voltage
Power Consumption
Overcurrent Protection
Contact Resistance
Turn-On Time
Minimum Applicable Load
Response Time
Overvoltage Category
Pollution Degree
Rated Insulation Voltage
(output contact)
Safety Output
3NO
Functional
Safety
Contact Configuration
Safety Output
Time-delay
3NO
EN ISO 13849-1: 2008
EN 954-1: 1996
EN 50178: 1997
EN 55011/A2: 2007
EN 61000-6-2: 2005
EN 61496-1: 2004
UL508/R2005-07 (Note 1)
CAN/CSA C22.2 No.14: 2005 (Note 1)
EN 60204-1: 2006
e (EN ISO13849-1)
4 (EN ISO13849-1)
0, 1 (IEC/EN 60204-1) (Note 2)
–10 to +55°C (no freezing)
30 to 85% (no condensation)
0 to 2000m (operating)
100 MΩ minimum
(500V DC megger, same measurement
positions as dielectric strength)
Between outside housing and internal circuit:
Between outputs of different poles:
Between input and output terminals:
Between power supply and output terminals:
300 m/s
each of 3 axes
100 m/s
in each of 3 axes
10 to 55 Hz, 1 octave/minute,
0.7 mmp-p in each of 3 axes, 20 sweeps,
5 to 55 Hz, 30 m/s
3 axes
Terminals: IP20 Housing: IP40
24V DC –15% to +10%
4.6W (26.4V DC)
Built-in, electronic (approx. 0.9A)
200 mΩ maximum (measured using 5 or
6V DC, 1A voltage drop method)
50 ms maximum
24V DC / 5 mA (reference value)
20 ms maximum (Note 3) (Note 4)
III (IEC60664-1)
2 (IEC60664-1)
250V (IEC60664-1)
2
2
, pulse width 11m sec, 3 times in
, pulse width 16m sec, 1000 times
Auxiliary Contact
2
, for 2 hours in each of
7.5 sec. (0.5, 1.0 … 7.0, 7.5); 15 sec. (1, 2 … 14, 15); 30 sec. (2, 4 … 28, 30)
2NC
2,500V AC, 1 minute
2,500V AC, 1 minute
3,750V AC,1 minute
2,500V AC,1 minute
Negative
Input
Dimensions
MANU
RESET
S33
S11 S12 S21 S22
HR2S-332N-T075
K1
41
K2
42
POW K1 K2
41
13
Y2
14
Note 1: UL and CSA are approved by TÜV SÜD America Inc., an accredited
Note 2: Safety output contact: Stop Category 0
Note 3: When measured at the rated voltage (at 20°C), excluding contact
Note 4: The time from when the safety input turns OFF to when the safety
Note 5: Leave 5 mm of space between the sides of the module when more
Note 6: The module is not suitable for use with a load less than the minimum
Note 7: The maximum current of the safety output contact is specified by the
•
42
SAFETY
RELAY MODULE
Mechanical Durability
Electrical Durability
Wire Size
Weight (approx.)
13
14
To prevent the safety output contact from overcurrent, use a fuse. To satisfy
Category 4, use a fuse with a maximum current of 3.6A. This fuse is not
required if the short circuit current is less than 5A.
23
A1
24
AUTO
RESET
23
24
45.0
Terminals
13-14
23-24
33-34
Terminals
41-42
Terminals
57-58
67-68
77-78
Terminals
45-46
33
A2
33
34
34
K3
K4
57
58
max. 7.5sec
max. 7.5sec
ERR.
NRTL.
Time-delay output contact: Stop Category 1
bounce time.
output turns OFF.
than 3A is continuously applied to the relay contact.
applicable load. Once a large load is applied, contacts may not
operate with a small load.
approved standard.
Category 4: 3.6A
57
58
68
67
0.5
0.5
K3 K4
1
1
67
68
77
78
77
78
4
4
45
45
46
46
24V DC –15% to +10%
Rated Load
(Note 5) (Note 6)
Safety
Circuit
No. of Outputs
Rated Load
(Note 6)
Safety
Circuit
No. of Outputs
Rated Load
(Note 5) (Note 6)
Safety
Circuit
No. of Outputs
Rated Load
(Note 6)
Safety
Circuit
No. of Outputs
Supply Voltage
AC15
DC13
AC15
DC13
AC15
DC13
AC15
DC13
Category 3: 5.0A
250V AC / 30V DC (resistive load) (Note 7)
Category 3 or lower: 5.0A maximum
Category 4 or lower: 3.6A maximum
240V AC / 2A cosø=0.3
24V DC / 1A L/R=48 ms
3 (NO contact output)
250V AC / 30V DC (resistive load)
Category 3 or lower: 5.0A maximum
Category 4 or lower: 3.6A maximum
240V AC / 2A cosø=0.3
24V DC / 1A L/R=48 ms
1 (NC contact output)
250V AC / 30V DC (resistive load) (Note 7)
Category 3 or lower: 5.0A maximum
Category 4 or lower: 3.6A maximum
240V AC / 2A cosø=0.3
24V DC / 1A L/R=48 ms
3 (NO contact output)
250V AC / 30V DC (resistive load)
Category 3 or lower: 5.0A maximum
Category 4 or lower: 3.6A maximum
240V AC / 2A cosø=0.3
24V DC / 1A L/R=48 ms
1 (NC contact output)
5,000,000 operations minimum
100,000 operations minimum
0.2 mm
320g
Terminal position (95.7)
2
to 1.5 mm
Terminal position (76.7)
111
HR2S-332N-T075
HR2S-332N-T15
HR2S-332N-T30
2
(24 to 16 AWG)
Part No.
All dimensions in mm
Package Quantity: 1
7