HR2S-301P IDEC, HR2S-301P Datasheet - Page 3

• Manufacturer Part Number: HR2S-301P
• Description: 47T1444
• Manufacturer: IDEC

HR2S-301P/HR2S-301N Safety Relay Modules
HR2S-301P/HR2S301N
Specifications
(110127)
Applicable Standards
Applicable Standards for Use
Performance level (PL)
Safety Category (Note 2)
Stop Category
Operating Temperature
Relative Humidity
Altitude
Insulation Resistance
Dielectric Strength
Shock Resistance
Bump
Vibration Resistance
Degree of Protection
Rated Voltage
Power Consumption
Overcurrent Protection
Contact Resistance
Turn-On Time
Minimum Applicable Load
Response Time
Overvoltage Category
Pollution Degree
Safety Output
3NO
Contact Configuration
Functional
Safety
Auxiliary Contact
EN ISO 13849-1: 2008
EN 954-1: 1996
EN 50178: 1997
EN 55011/A2: 2007
EN 61000-6-2: 2005
IEC/EN 61496-1: 2006
UL508/R2005-07 (Note 1)
CAN/CSA C22.2 No.14: 2005 (Note 1)
EN 60204-1: 2006
e (EN ISO 13849-1)
3 or 4 (EN ISO 13849-1)
0 (IEC/EN 60204-1)
–10 to +55°C (no freezing)
30 to 85% (no condensation)
0 to 2000m (operating)
100Ω minimum
(500V DC megger, same measurement
positions as dielectric strength)
Between outside housing and internal circuit:
Between outputs of different poles:
Between input and output terminals:
Between power supply and output terminals:
300 m/s
each of 3 axes
100 m/s
in each of 3 axes
10 to 55 Hz, 1 octave/minute,
0.7 mmp-p in each of 3 axes, 20 sweeps,
5 to 55 Hz, 30 m/s
3 axes
Terminals: IP20 Housing: IP40
24V DC –15% +10%
2.2W (26.4V DC)
Built-in, electronic (approx. 0.9A)
200 mΩ maximum (Note 3)
50 ms maximum (Note 4)
24V DC / 5 mA (Reference value)
20 ms maximum (Note 4) (Note 5)
III (IEC60664-1)
2 (IEC60664-1)
1NC
2
2
, pulse width 11m sec, 3 shocks in
, pulse width 16m sec, 1000 times
2
, for 2 hours in each of
2,500V AC ,1 minute
2,500V AC, 1 minute
2,500V AC, 1 minute
3,750V AC,1 minute
Negative
Positive
Input
Dimensions
Note 1: UL and CSA are approved by TÜV SÜD America Inc., an accredited
Note 2: HR2S-301N is recommended for use in category 4 safety
Note 3: Measured using 5 or 6V DC, 1A voltage drop method.
Note 4: When measured at the rated voltage (at 20°C), excluding contact
Note 5: The time from when the safety input turns OFF to when the safety
Note 6: Leave 5 mm of space between the sides of the module when more
Note 7: The module is not suitable for use with a load less than the minimum
Note 8: The maximum current of the safety output contact is specified by the
•
Rated Insulation Voltage
(output contact)
Mechanical Durability
Electrical Durability
Wire Size
Weight (approx.)
To prevent the safety output contact from overcurrent, use a fuse. To satisfy
Category 4, use a fuse with a maximum current of 3.6A. This fuse is not
required if the short circuit current is less than 5A.
S33
RESET
S11 S12 S21 S22
HR2S-301P
MANU
K1
K2
41
42
Terminals
13-14
23-24
33-34
Terminals
41-42
POW
22.5
S34
41
42
13
14
24V DC –15% to +10%
24V DC –15% to +10%
SAFETY
RELAY MODULE
K1 K2
13
14
23
A1
AUTO
RESET
NRTL.
applications. The requirements of the safety category must be
determined according to the safety equipment. We recommend that
you consult a third party organization.
Categories may change depending on the combination of the safety
equipment. Categories may also change depending on the output
contact ratings.
bounce time.
output turns OFF.
than 3A is continuously applied to the relay contact.
applicable load. Once a large load is applied, contacts may not
operate with a small load.
approved standard.
Category 4
Category 3
24
23
24
Supply Voltage
33
A2
34
33
34
Rated Load
(Note 6) (Note 7)
Safety
Circuit
No. of Outputs
Rated Load
(Note 7)
Safety
Circuit
No. of Outputs
HR2S-301N, HR2S-301P + Type 4 OSSD’s
HR2S-301P
AC15
DC13
AC15
DC13
250V (IEC60664-1)
250V AC / 30V DC (resistive load) (Note 8)
Category 3 or lower: 5.0A maximum
Category 4 or lower: 3.6A maximum
240V AC / 2A cosø=0.3
24V DC / 1A L/R=48 ms
3 (NO contact output)
250V AC / 30V DC (resistive load)
Category 3 or lower: 5.0A maximum
Category 4 or lower: 3.6A maximum
240V AC / 2A cosø=0.3
24V DC / 1A L/R=48 ms
1 (NC contact output)
5,000,000 operations minimum
100,000 operations minimum
0.2 mm
200g
Terminal position (95.7)
2
Terminal position (76.7)
to 1.5 mm
111
HR2S-301P
HR2S-301N
2
Part No.
(24 to 16 AWG)
All dimensions in mm
Package Quantity: 1
3.6A
5.0A
3