SI3018-F-GS Silicon Laboratories Inc, SI3018-F-GS Datasheet - Page 29
![IC VOICE DAA GCI/PCM/SPI 16SOIC](/photos/6/80/68073/16-soic__3_9mmwidth__sml.jpg)
SI3018-F-GS
Manufacturer Part Number
SI3018-F-GS
Description
IC VOICE DAA GCI/PCM/SPI 16SOIC
Manufacturer
Silicon Laboratories Inc
Type
Chipsetr
Datasheet
1.SI2434-C-GT.pdf
(74 pages)
Specifications of SI3018-F-GS
Package / Case
16-SOIC (3.9mm Width)
Function
Data Access Arrangement (DAA)
Interface
Serial
Number Of Circuits
1
Voltage - Supply
3 V ~ 3.6 V
Current - Supply
8.5mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Includes
Line Voltage Monitor, Loop Current Monitor, Overload Detection, Parallel Handset Detection, Polarity Reversal Detection, TIP and
Product
Modem Module
Supply Voltage (min)
3 V
Supply Current
15 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power (watts)
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
4.20. Extended AT Commands
The extended AT commands are supported by the Si2457/34/15/04 and are described in Tables 11 through 13.
&$
&D0
&D1
&D2
&D3
&F
&Gn
&G3
&G4
&G5
&G6
&G7
&G8
&G9
&G10
&G11
&G12
&G13
&G14
&G15
&G16
&G17
&Hn
&H0
&H1
&H2
&H3
Command
Display AT& current settings.
ESC is not used
ESC escapes to command mode from data mode if also enabled by HES U70, bit 15.
ESC assertion during a modem connection causes the modem to go on-hook and return to com-
mand mode.
ESC assertion causes ATZ command (reset and return OK result code).
Restore factory default settings.
Line connection rate limit—This command sets an upper limit on the line speed that the Si2457/34/
15/04 can connect. Note that the &Hn commands may limit the line speed as well (&Gn not used for
&H0 or &H1). Not all modulations support rates given by &G. Any improper setting will be ignored.
1200 bps max
2400 bps max (default for Si2404)
4.8 kbps max
7.2 kbps max
9.6 kbps max
12 kbps max
14.4 kbps max (default for Si2415)
16.8 kbps max
19.2 kbps max
21.6 kbps max
24 kbps max
26.4 kbps max
28.8 kbps max
31.2 kbps max
33.6 kbps max (default for Si2457 and Si2434)
Switched network handshake mode—&Hn commands must be on a separate command line from
ATD, ATA, or ATO commands.
V.90 with automatic fallback (56 kbps to 300 bps) (default for Si2457)
V.90 only (56 kbps to 28 kbps)
V.34 with automatic fallback (33.6 kbps to 300 bps) (default for Si2434)
V.34 only (33.6 kbps to 2400 bps)
Table 11. Extended AT& Command Set (Command Defaults in Bold)
Rev. 1.1
Action
Si2457/34/15/04
29