LQ215M1LGN2 Sharp Electronics, LQ215M1LGN2 Datasheet
![no-image](/images/manufacturer_photos/0/6/602/sharp_electronics_sml.jpg)
LQ215M1LGN2
Specifications of LQ215M1LGN2
Related parts for LQ215M1LGN2
LQ215M1LGN2 Summary of contents
Page 1
... Technical Document LCD Specification LCD Group LQ215M1LGN2 LCD Module Product Specification January 2010 Full-HD module with LVDS interface features a fast response time of 5 ms, very wide viewing cone, brightness of 300 nits, and 1000:1 contrast ratio. ...
Page 2
...
Page 3
... RECORDS OF REVISION LQ215M1LGN2 SPEC No. DATE LD-22112 Jan. 29. 2010 REVISED No. PAGE SUMMARY NOTE 1st Issue ...
Page 4
... Application This specification applies to the color 21.5 Full HD TFT-LCD module, LQ215M1LGN2. ◎This specification are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. ◎ ...
Page 5
Mechanical Specifications Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment *1.Note: excluding back light cables, cover and pet sheets. The thickness of module (D) doesn’t contain the ...
Page 6
Input Terminals 4-1. TFT-LCD panel driving CN1 (Interface signals and +5.0V DC power supply) Using connectors Corresponding connectors (Sharp is not responsible to its product quality, if the user applies a connector not corresponding to the above model.) Pin ...
Page 7
LVDS Data Mapping Previous Cycle CK1IN+/- R1IN0+/- R14’ R13’ R1IN1+/- G15’ G14’ R1IN2+/- NA B15’ R1IN3+/- G17’ B16’ CK2IN+/- R2IN0+/- R24’ R23’ R2IN1+/- G25’ G24’ R2IN2+/- NA B25’ R2IN3+/- B26’ G27’ Display Enable NA : Not Available ...
Page 8
Backlight CN2, 3 (Upper/Lower FPC Connector Pin Assignment) Using connector Corresponding FFC specification :Temperature = 80 CN2 and CN3 are the same pin assignment. Pin No Symbol 1 IRLED1 2 IRLED1 3 IRLED2 4 VLED 5 VLED 6 VLED ...
Page 9
Electrical Characteristics 6-1. TFT-LCD panel driving Parameter Supply voltage Current dissipation Black White Mosaic Permissive input ripple voltage Differential input High threshold voltage Low Terminal resistor 【Note1】 Common mode voltage of LVDS driver. CM 【Note2】 1)On-off conditions ...
Page 10
Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition whereas black pattern is displayed. 【Note4】The specified current is under the Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition whereas white pattern is displayed. 【Note5】The specified ...
Page 11
Timing characteristics of input signals 7-1. Timing characteristics Parameter Clock signal Frequency Horizontal Horizontal period Horizontal period(High) Vertical Vertical period Vertical period(High) frequency 【Note】 In case of using the long vertical period, the deterioration of display quality, flicker etc. ...
Page 12
Input Data Signals and Display Position on the screen (1、1) (1,2) 1・1 1・2 1・3 2・1 2・2 3・1 1080・1 Display Position of Data (V,H) Two pixels-data are sampled at the same time. *A side ...
Page 13
Input Signals, Basic Display Colors and Gray Scale of Each Color 8-1 8bit input Colors & Gray Gray scale Scale Black - Blue - Green - 0 ...
Page 14
Optical Characteristics Parameter Symbol Viewing θ11 Vertical angle θ12 range θ21,θ22 Horizontal Contrast ratio CR Response Rise τr Time Fall τd Rise+Fall τr +τd Chromaticity of x White y Chromaticity of x Red y Chromaticity of x Green y ...
Page 15
Characteristics Measurements: 【Note6】Definitions of viewing angle range: 【Note7】Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio(CR) = 【Note8】Definition of white uniformity: White uniformity is defined as the following with nine measurements D/10 W/10 1 ...
Page 16
We measured luminance in case there are a window frame and in case there are not a window frame with A points & B points of the following figure. Then, we compared the measured values. |Luminance ...
Page 17
Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable sure to design the cabinet so that the module can be installed without any extra stress such as warp or ...
Page 18
Packing form a) Piling number of cartons : maximum 2 cartons b) Packing quantity in one carton : 8 modules c) Carton size : 565mm(W)×250mm(D)×420mm(H) d) Total mass of one carton filled with full modules : 14.5kg(Max.) e) Packing ...
Page 19
Shipping Pallet Package a) Total mass of two pallets filled with full modules : 505kg(Max.) Step 1 Place a pallet specially, spec is:1130mm*1100mm*140mm,as fig4. Step 2 Stack cartons on the Pallet in 2 tiers,8 cartons in a tier, total ...
Page 20
No Test item 1 High temperature storage test 2 Low temperature storage test 3 High temperature & high humidity operation test 4 High temperature operation test 5 Low temperature operation test 6 Vibration test (non- operating) 7 ...
Page 21
... Lot No. and indication Bar Code Label: LQ215M1LGN2 Z 1 Serial No Serial ID includes the information as below: 1. Year: Final digit of the A.D. EX.”0” for 2010 2. Month: 1~ and Z. (X=Oct. Y=Nov. Z=Dec.) 3. Day: 1~9,A to X.(please refer Day Code table) 4. Sharp internal use 5. Serial No: 0~99999, Over 10Kpcs use A, B, C… ...
Page 22
... If any problem occurs in relation to the description of this specification , it shall be resolved through discussion with spirit of cooperation. ① Model No. (LQ215M1LGN2) ② Lot No. (Date) ③ Quantity 8 pcs ...
Page 23
... Fig7.LQ215M1LGN2 OUTLINE DIMENSIONS ...
Page 24
... MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable, or responsible in any way, for any incidental or consequential economic or property damage. EUROPE Sharp Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: 49 (0)180 507 35 07 Fax: (49) 40-2376-2232 www ...