MAX3100EPD+ Maxim Integrated Products, MAX3100EPD+ Datasheet - Page 7

• Manufacturer Part Number: MAX3100EPD+
• Description: IC UART SPI MICROWIRE-COMP 14DIP
• Manufacturer: Maxim Integrated Products
• Type: SPI/MICROWIRE-Compatible UARTr

Specifications of MAX3100EPD+

• Features: Low Power
• Number Of Channels: 1, UART
• Fifo's: 8 Byte
• Protocol: RS232, RS485
• Voltage - Supply: 2.7 V ~ 5.5 V
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Cmos: Yes
• Mounting Type: Through Hole
• Package / Case: 14-DIP (0.300", 7.62mm)
• Data Rate: 115.2 Kbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Supply Current: 0.27 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Description/function: SPI/MICROWIRE-compatible UART
• Mounting Style: Through Hole
• Operating Supply Voltage: 2.7 V to 5.5 V
• No. Of Channels: 1
• Supply Voltage Range: 2.7V To 5.5V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: DIP
• No. Of Pins: 14
• Uart Type: Asynchronous
• Supply Voltage Min: 2.7V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The receiver section receives data in serial form. The
MAX3100 detects a start bit on a high-to-low RX transi-
tion (Figure 3). An internal clock samples data at 16
times the data rate. The start bit can occur as much as
one clock cycle before it is detected, as indicated by
the shaded portion. The state of the start bit is defined
as the majority of the 7th, 8th, and 9th sample of the
internal 16x baud clock. Subsequent bits are also
majority sampled. Receive data is stored in an 8-word
FIFO. The FIFO is cleared if it overflows.
The on-board oscillator can use a 1.8432MHz or
3.6864MHz crystal, or it can be driven at X1 with a 45%
to 55% duty-cycle square wave.
Figure 3. Start-Bit Timing
Figure 4. SPI Interface (Write Configuration)
DOUT
SCLK
BLOCK
BAUD
DIN
CS
RX
1
R
A
1
1
_______________________________________________________________________________________
T
1
2
2
FEN
0
3
3
SHDN
0
4
4
TM
0
5
5
RM
0
6
6
PM
0
7
SPI/MICROWIRE-Compatible
7
RAM
0
8
ONE BAUD PERIOD
8
IR
0
9
9
The bit streams for DIN and DOUT consist of 16 bits,
with bits assigned as shown in the MAX3100
Operations section. DOUT transitions on SCLK’s falling
edge, and DIN is latched on SCLK’s rising edge (Figure
4). Most operations, such as the clearing of internal
registers, are executed only on CS’s rising edge. The
DIN stream is monitored for its first two bits to tell the
UART the type of data transfer being executed (Write
Config, Read Config, Write Data, Read Data).
Only 16-bit words are expected. If CS goes high in the
middle of a transmission (any time before the 16th bit),
the sequence is aborted (i.e., data does not get written
to individual registers). Every time CS goes low, a new
16-bit stream is expected. An example of a write con-
figuration is shown in Figure 4.
ST
0
10
10
MAJORITY
SAMPLER
CENTER
PE
0
11
11
0
L
UART in QSOP-16
12
12
B3
0
13
13
B2
0
14
14
B1
0
15
15
B0
0
16
16
UPDATED
SPI Interface
DATA
7