ISD4002-120E Nuvoton Technology Corporation of America, ISD4002-120E Datasheet - Page 7
![IC VOICE REC/PLAY 120SEC 28-TSOP](/photos/6/98/69885/256-28-tsop_sml.jpg)
ISD4002-120E
Manufacturer Part Number
ISD4002-120E
Description
IC VOICE REC/PLAY 120SEC 28-TSOP
Manufacturer
Nuvoton Technology Corporation of America
Series
ISD4002r
Datasheet
1.ISD4002-120E.pdf
(37 pages)
Specifications of ISD4002-120E
Interface
SPI/Microwire
Filter Pass Band
3.4kHz
Duration
120 Sec
Mounting Type
Surface Mount
Package / Case
28-TSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
ISD4002120E
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISD4002-120E
Manufacturer:
ISD
Quantity:
552
Part Number:
ISD4002-120EI
Manufacturer:
ISD
Quantity:
20 000
Company:
Part Number:
ISD4002-120EY
Manufacturer:
NUVOTON
Quantity:
2 000
Company:
Part Number:
ISD4002-120EYI
Manufacturer:
NUVOTON
Quantity:
2 000
Part Number:
ISD4002-120EYI
Manufacturer:
ISD
Quantity:
20 000
6. PIN DESCRIPTION
[1]
connected to this pin can drive a load as small as 5 KΩ. When in record, a resistor connects AUD OUT to the
internal 1.2-volt analog ground supply. This resistor is approximately 850 KΩ, but will vary somewhat according to
the sample rate of the device. This relatively high impedance allows this pin to be connected to an audio bus
without loading it down.
AUD OUT
PIN NAME
V
The AUD OUT pin is always at 1.2 volts when the device is powered up. When in playback, the output buffer
SSA
MOSI
MISO
SS
NC
/ V
SSD
[1]
5-10, 15,
11, 12,
SOIC /
23 / 4
19-22
PDIP
13
1
2
3
PIN NO.
16, 19, 21,
1, 17, 18 /
23, 27, 28
3, 4, 13-
TSOP
10
11
12
20
9
Slave Select: This input, when LOW, will select the
ISD4002 device.
Master Out Slave IN: This is the serial input to the
ISD4002 device when it is configured as slave. The master
microcontroller places data on the MOSI line one half-cycle
before the rising edge of SCLK for clocking into the device.
Master In Slave Out: This is the serial output (open drain)
of the ISD4002 device. This output goes into a high-
impedance state if the device is not selected.
Ground: The ISD4002 series utilizes separate analog and
digital ground busses. The analog ground (V
should be tied together as close as possible and connected
through a low-impedance path to power supply ground.
The digital ground (V
a separate low-impedance path to power supply ground.
These ground paths should be large enough to ensure that
the impedance between the V
less than 3 Ω. The backside of the die is connected to V
through the substrate. For chip-on-board design, the die
attach area must be connected to V
Not connected
Audio Output: This pin provides an audio output of the
stored data and is recommended be AC coupled. It is
capable of driving a 5 KΩ impedance R
- 7 -
Publication Release Date: September 2003
SSD
FUNCTION
) pin should be connected through
ISD4002 SERIES
SSA
pins and the V
SS
or left floating.
EXT
.
SSD
SSA
Revision 1
) pins
pin is
SS