MAX97001EWP+T Maxim Integrated Products, MAX97001EWP+T Datasheet - Page 33

• Manufacturer Part Number: MAX97001EWP+T
• Description: IC AUDIO SUBSYSTEM 20WLP
• Manufacturer: Maxim Integrated Products
• Series: DirectDrive™r
• Type: Class Dr

Specifications of MAX97001EWP+T

• Output Type: 1-Channel (Mono) with Stereo Headphones
• Max Output Power X Channels @ Load: 920mW x 1 @ 8 Ohm; 37mW x 2 @ 16 Ohm
• Voltage - Supply: 2.7 V ~ 5.5 V
• Features: Depop, Differential Inputs, I²C, Mute, Shutdown, Volume Control
• Mounting Type: Surface Mount
• Package / Case: 20-WLP
• Product: Class-D
• Output Power: 550 mW, 700 mW, 920 mW
• Available Set Gain: 12 dB
• Common Mode Rejection Ratio (min): 32 dB, 55 dB
• Thd Plus Noise: 0.05 %
• Operating Supply Voltage: 2.7 V to 5.5 V
• Supply Current: 2.7 V
• Maximum Power Dissipation: 1040 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Input Signal Type: Differential, Single
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential
• Supply Voltage (max): 5.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: MAX97001EWP+T

Figure 12. Reading One Byte of Data from the MAX97001
Figure 13. Reading n-Bytes of Data from the MAX97001
Traditional Class D amplifiers require an output filter to
recover the audio signal from the amplifier’s output. The
filters add cost, increase the solution size of the amplifier,
and can decrease efficiency and THD+N performance.
The traditional PWM scheme uses large differential out-
put swings (2 x V
rents. Any parasitic resistance in the filter components
results in a loss of power, lowering the efficiency.
The MAX97001 does not require an output filter. The
device relies on the inherent inductance of the speaker
coil and the natural filtering of both the speaker and
the human ear to recover the audio component of the
square-wave output. Eliminating the output filter results
in a smaller, less costly, more efficient solution.
Because the frequency of the MAX97001 output is well
beyond the bandwidth of most speakers, voice coil
movement due to the square-wave frequency is very
small. Although this movement is small, a speaker not
designed to handle the additional power can be dam-
aged. For optimum results, use a speaker with a series
inductance > 10FH. Typical 8I speakers exhibit series
inductances in the 20FH to 100FH range.
S
Audio Subsystem with Mono Class D Speaker
ACKNOWLEDGE FROM MAX97001
S
ACKNOWLEDGE FROM MAX97001
SLAVE ADDRESS
SLAVE ADDRESS
Applications Information
DD(P-P)
Filterless Class D Operation
R/W
R/W
0
) and causes large ripple cur-
0
ACKNOWLEDGE FROM MAX97001
and Class H Headphone Amplifiers
ACKNOWLEDGE FROM MAX97001
REGISTER ADDRESS
REGISTER ADDRESS
REPEATED START
REPEATED START
A
Sr
ACKNOWLEDGE FROM MAX97001
A
Sr
ACKNOWLEDGE FROM MAX97001
SLAVE ADDRESS
GSM radios transmit using time-division multiple access
(TDMA) with 217Hz intervals. The result is an RF signal
with strong amplitude modulation at 217Hz and its har-
monics that are easily demodulated by audio amplifiers.
The MAX97001 is designed specifically to reject RF
signals; however, PCB layout has a large impact on the
susceptibility of the end product.
In RF applications, improvements to both layout and
component selection decreases the MAX97001’s sus-
ceptibility to RF noise and prevent RF signals from being
demodulated into audible noise. Trace lengths should
be kept below 1/4 of the wavelength of the RF frequency
of interest. Minimizing the trace lengths prevents them
from functioning as antennas and coupling RF signals
into the MAX97001. The wavelength (l) in meters is
given by:
where c = 3 x 10
interest.
Route audio signals on middle layers of the PCB to allow
ground planes above and below to shield them from RF
interference. Ideally, the top and bottom layers of the
PCB should primarily be ground planes to create effec-
tive shielding.
SLAVE ADDRESS
R/W
R/W
1
A
1
8
NOT ACKNOWLEDGE FROM MASTER
A
m/s, and f = the RF frequency of
l = c/f
DATA BYTE
1 BYTE
REGISTER ADDRESS POINTER
DATA BYTE
AUTOINCREMENT INTERNAL
1 BYTE
RF Susceptibility
REGISTER ADDRESS POINTER
AUTOINCREMENT INTERNAL
A
A
P
P
33