1734081-1 TE Connectivity, 1734081-1 Datasheet - Page 2

• Manufacturer Part Number: 1734081-1
• Description: USB Connectors RCPT 4 POS SERIES A
• Manufacturer: TE Connectivity
• Series: Ar

Specifications of 1734081-1

• Product: USB Type A Connectors
• Standard: USB
• Number Of Ports: 1
• Gender: Female
• Connector Type: USB Type A Receptacle
• Number Of Positions / Contacts: 4
• Size: Standard
• Orientation: Right Angle
• Mount Location: Top
• Termination Method: Solder
• Tail Length (mm [in]): 2.8 [0.11]
• Locking Feature: Without
• Led: Without
• Panel Ground: Without
• Pcb Mount Retention Type: Kinked Leg(s)
• Shell Plating: Nickel over Copper
• Assembly Process Feature: Without Pick and Place Cover
• Locating Post(s): Without
• Number Of Positions: 4
• Contact Termination Type: Through Hole
• Contact Plating, Mating Area, Material: Gold
• Contact Plating, Mating Area, Thickness (µm [?in]): 0.762 [30]
• Housing Color: Black
• Industry Standard: USB 2.0
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Rohs/elv Compliance History: Always was RoHS compliant
• Usb-if Test Id Number (tid): 65000561
• Applies To: Printed Circuit Board
• Pcb Thickness, Recommended (mm [in]): 1.60 [0.063]
• Packaging Method: Tray
• Lead Free Status / Rohs Status: Details

Rev
10
11 Physical Shock
2 Contact Resistance
3
4 Insulation Resistance
5 Temperature Rising
6 Contact Capacitance
7
8 Connector Unmating
9 Durability
1 Examination of Product
Dielectric withstanding
Voltage
Connector Mating
Force
Force
Vibration
The product shall be designed to meet the electrical, mechanical and environmental performance
requirements specified in Figure 1. All tests shall be performed at ambient environmental conditions per
TE specification 109-1 test requirements and procedure summary.
B
TEST ITEM
3.4. PERFORMANCE REQUEIREMENT AND TEST DESCRIPTION
3.5. TEST REQUIREMENTS AND PROCEDURES SUMMARY
Meets requirements of product
drawing. No physical damage.
30 m Ohm Max
No creeping discharge or
flashover shall occur.
Current leakage: 0.5 mA MAX
1000 M Ohm Min.
30
current
2 pF Maximum per Contact
3.57kgf [35N] Max.
1.02kgf [10N] Min.
See Note
No electrical discontinuity
greater than 1µsec shall occur.
See Note.
No electrical discontinuity
greater than 1µsec shall occur.
See Note.
℃
Max. Under loaded rating
MECHANICAL REQUIREMENT
REQUIREMENT
ELECTRICAL REQUIREMENT
Figure 1（Cont.）
Visual inspection.
Subject mated contacts assembled in
housing to 20mV Max open circuit at
100mA Max. EIA-364-23. Refer to Fig.3
500 VAC for 1minute
Test between adjacent circuits of
unmated connector. EIA-364-20B
Impressed voltage 500 VDC.
Test between adjacent circuits of
unmated connector. EIA-364-21C
1.5A at 250V AC minimum. When
measured at an ambient temperature of
25℃. EIA 364-70 Method B.
Test between adjacent circuits of
unmated connector at 1 KHz.
Operation Speed：12.5 mm/min.
Measure the force required to mate
connector. EIA-364-13B
Operation Speed：12.5 mm/min.
Measure the force required to unmate
connector. EIA-364-13B
Mate and unmated Connector
assemblies for 1500 cycles at maximum
rated of 200 cycles per hour.
EIA-364-09
Subject mated connectors to 10-55-10
Hz traversed in 1minutes at 1.52mm
amplitude 2 Hours each of 3 mutually
perpendicular planes.
100mA Max. Applied. EIA-364-28D
Accelerate Velocity：294m/s2 (30G)
Waveform：Half-sine shock plus
Duration：11msec
No. of Drops：3 drops each to normal
and reversed directions of X, Y and Z
axes, totally 18 drops, passing DC
100mA max. current during the test.
EIA-364-27B
PROCEDURE
108-57505
2 of 5