1734081-1 TE Connectivity, 1734081-1 Datasheet - Page 3

• Manufacturer Part Number: 1734081-1
• Description: USB Connectors RCPT 4 POS SERIES A
• Manufacturer: TE Connectivity
• Series: Ar

Specifications of 1734081-1

• Product: USB Type A Connectors
• Standard: USB
• Number Of Ports: 1
• Gender: Female
• Connector Type: USB Type A Receptacle
• Number Of Positions / Contacts: 4
• Size: Standard
• Orientation: Right Angle
• Mount Location: Top
• Termination Method: Solder
• Tail Length (mm [in]): 2.8 [0.11]
• Locking Feature: Without
• Led: Without
• Panel Ground: Without
• Pcb Mount Retention Type: Kinked Leg(s)
• Shell Plating: Nickel over Copper
• Assembly Process Feature: Without Pick and Place Cover
• Locating Post(s): Without
• Number Of Positions: 4
• Contact Termination Type: Through Hole
• Contact Plating, Mating Area, Material: Gold
• Contact Plating, Mating Area, Thickness (µm [?in]): 0.762 [30]
• Housing Color: Black
• Industry Standard: USB 2.0
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Rohs/elv Compliance History: Always was RoHS compliant
• Usb-if Test Id Number (tid): 65000561
• Applies To: Printed Circuit Board
• Pcb Thickness, Recommended (mm [in]): 1.60 [0.063]
• Packaging Method: Tray
• Lead Free Status / Rohs Status: Details

Rev
12
13 Solder ability
12
12
12
12
12
15 Thermal Shock
16
17
18 Salt Spray
Contact Retention
Force
Resistance to Wave
Soldering Heat
Resistance to Wave
Soldering Heat
Resistance to Reflow
Soldering Heat
Resistance to Reflow
Soldering Heat
Resistance to Reflow
Soldering Heat
Humidity-Temperature
Cycle
Temperature Life
(Heat Aging)
B
TEST ITEM
1000 gf Min.
The inspected area of each
lead must have 95% solder
coverage minimum.
No physical damage shall
occur.
No physical damage shall
occur.
No physical damage shall
occur.
No physical damage shall
occur.
No physical damage shall
occur.
See Note
See Note
See Note
No detrimental corrosion
allowed in contact area and
base metal exposed.
ENVIRONMENTAL REQUIREMENTS
MECHANICAL REQUIREMENT
REQUIREMENT
Figure 1（End）
Measure the contact retention force with
Steam Aging Preconditioning：
1. Intended for nontin and nontin-alloy
lead finishes for 93+3/-5℃、1hrs.
2. Intended for tin and tin-alloy lead
finishes for 93+3/-5℃、8hrs.
<JESD22-B102D, Condition C>
Solder pot temperature: 245±5℃, 5sec
Solder Temp.：240±5℃, 10±0.5sec.
TE spec. 109-202, Condition A
Solder Temp.：265±5℃, 10±0.5sec.
TE spec. 109-202, Condition B
Pre Heat：100~150℃, 60 sec Max.
Heat：210℃ Min., 30 sec Max.
Peak Temp.：240℃ Max., 10±0.5sec.
Pre-soak condition, 85 ℃ /85 ﹪ RH for
168 hours.
Pre Heat：150~180℃, 90±30sec.
Heat：230℃ Min., 30±10sec.
Peak Temp.：245+0/-5℃, 10~30sec.
Duration：3 cycles
TE spec. 109-201, Condition A
Pre-soak condition, 85 ℃ /85 ﹪ RH for
168 hours.
Pre Heat：150~180℃, 90±30sec.
Heat：230℃ Min., 30±10sec.
Peak Temp.：260+0/-5℃, 20~40sec.
Duration：3 cycles
TE spec. 109-201, Condition B
Mated Connector
-55+/-3 (30 minutes), +85+/
minutes)
Perform this a cycle, repeat 10 cycles
EIA-364-32C
Mated Connector
25~65
(seven complete cycles) EIA-364-31B.
Mated Connector
85
Subject mated connectors to 35+/-2 ℃
and 5+/-1% salt condition for 48hours.
After test, rinse the sample with water
and recondition the room temperature
for 1 hour. EIA-364-26B.
Tensile strength tester.
℃
, 250 hours, EIA
℃
℃
, 90~95% RH,
PROCEDURE
-364-17B.
168 Hours
108-57505
-2 (30
℃
3 of 5