TDA8567Q/N3S,112 NXP Semiconductors, TDA8567Q/N3S,112 Datasheet - Page 5

• Manufacturer Part Number: TDA8567Q/N3S,112
• Description: IC AMP CLASS B OUTPUT DBS23
• Manufacturer: NXP Semiconductors
• Type: Class Br

Specifications of TDA8567Q/N3S,112

• Output Type: 4-Channel (Quad)
• Package / Case: 23-SIL (Bent and Staggered Leads)
• Max Output Power X Channels @ Load: 35W x 4 @ 4 Ohm
• Voltage - Supply: 6 V ~ 18 V
• Features: Depop, Differential Inputs, Mute, Short-Circuit and Thermal Protection, Standby
• Mounting Type: Through Hole
• Product: Class-B
• Output Power: 35 W
• Available Set Gain: 26 dB
• Thd Plus Noise: 0.05 %
• Operating Supply Voltage: 14.4 V
• Maximum Power Dissipation: 60000 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Audio Load Resistance: 4 Ohms
• Input Signal Type: Single
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential
• Supply Type: Single
• Supply Voltage (max): 18 V
• Supply Voltage (min): 6 V
• Lead Free Status / RoHS Status: Lead free by exemption / RoHS compliant by exemption
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free by exemption / RoHS compliant by exemption
• Other names: 935289253112

Philips Semiconductors
FUNCTIONAL DESCRIPTION
The TDA8567Q contains four identical amplifiers which
can be used for bridge applications. The gain of each
amplifier is fixed at 26 dB.
Mode select switch (pin 15)
Since this pin has a low input current (<80 A), a low cost
supply switch can be applied.
To avoid switch-on plops, it is advised to keep the amplifier
in the mute mode during 150 ms (charging of the input
capacitors at pins 10, 11, 13 and 14). When switching
from standby to mute, the slope should be at least 18 V/s.
This can be realized by:
Diagnostic output (pin 9)
D
At the onset of clipping of one or more output stages, the
dynamic distortion detector becomes active and pin 9
goes LOW. This information can be used to drive a sound
processor or DC volume control to attenuate the input
signal and so limit the distortion. The output level of pin 9
is independent of the number of channels that are clipping
(see Fig.4).
1998 Sep 23
handbook, halfpage
YNAMIC
Standby: low supply current (<100 A)
Mute: input signal suppressed
Operating: normal on condition.
Microprocessor control
External timing circuit (see Fig.3).
4
amplifier
25 W BTL quad car radio power
D
ISTORTION
Fig.3 Mode select switch circuitry.
V P
D
ETECTOR
BZX79C/3.9V
10 k
(DDD)
47 F
MGD959
MODE
5
S
When a short-circuit occurs at one or more outputs to
ground or to the supply voltage, the output stages are
switched off until the short-circuit is removed and the
device is switched on again, with a delay of approximately
10 ms after removal of the short-circuit. During this
short-circuit condition, pin 9 is continuously LOW.
When a short-circuit occurs across the load of one or more
channels, the output stages are switched off during
approximately 10 ms. After that time it is checked during
approximately 50 s to determine whether the short-circuit
is still present.
Due to this duty cycle of 50 s/10 ms the average current
consumption during this short-circuit condition is very low.
During this short-circuit condition, pin 9 is LOW for 10 ms
and HIGH for 50 s (see Fig.5). The protection circuits of
all channels are coupled. This means that if a short-circuit
condition occurs in one of the channels, all channels are
switched off. Consequently, the power dissipation in any
short-circuit condition is very low.
T
When the virtual junction temperature T
pin 9 goes LOW.
O
The diagnostic pin has an open collector output, so more
devices can be tied together. An external pull-up resistor is
needed.
handbook, halfpage
EMPERATURE PRE
HORT
PEN COLLECTOR OUTPUTS
-
CIRCUIT DIAGNOSTIC
V 9
V o
V P
Fig.4 Distortion detector waveform.
0
0
-
WARNING
Product specification
TDA8567Q
vj
reaches 145 C,
MGG155
t