LM4854LD/NOPB National Semiconductor, LM4854LD/NOPB Datasheet - Page 8

IC AMP AUDIO PWR 2.3W MONO 14LLP

LM4854LD/NOPB

Manufacturer Part Number
LM4854LD/NOPB
Description
IC AMP AUDIO PWR 2.3W MONO 14LLP
Manufacturer
National Semiconductor
Series
Boomer®r
Type
Class ABr
Datasheet

Specifications of LM4854LD/NOPB

Output Type
1-Channel (Mono) with Stereo Headphones
Max Output Power X Channels @ Load
2.3W x 1 @ 3.2 Ohm; 200mW x 2 @ 16 Ohm
Voltage - Supply
2.4 V ~ 5.5 V
Features
Depop, Shutdown, Standby, Thermal Protection
Mounting Type
Surface Mount
Package / Case
14-LLP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*LM4854LD
LM4854LD
LM4854LDNOPB
LM4854LDNOPBTR
LM4854LDNOPBTR
LM4854LDTR
www.national.com
P
THD+N
VOUT
XTALK
S/N
Symbol
O
Electrical Characteristics : SE Operation (V
Note 2: All voltages are measured with respect to the GND pin unless other wise specified.
Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions that
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
allowable power dissipation is P
currents for more information.
Note 5: Human body model, 100pF discharged through a 1.5kΩ resistor.
Note 6: Machine Model, 220pF-240pF discharged through all pins.
Note 7: The given θ
Note 8: Typicals are measured at 25˚C and represent the parametric norm.
Note 9: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 10: Datasheet minimum and maximum specification limits are guaranteed by design, test, or statistical analysis.
Note 11: Output power is measured at the amplifier’s package pins.
Note 12: When driving 4Ω loads and operating on a 5V supply, the LM4854LD must be mounted to a circuit board that has a minimum of 2.5in2 of exposed,
uninterrupted copper area connected to the LLP package’s exposed DAP.
The following specifications apply for for the circuit shown in Figure 1 and a measurement bandwith of 20Hz to 80kHz, unless
otherwise specified. Limits apply for T
Output Power (Note 11)
Total Harmonic Distortion+Noise
Output Voltage Swing
Channel Separation
Signal-to-Noise Ratio
JA
is for an LM4854 packaged in an LDA14A with the Exposed-DAP soldered to an exposed 2in2 area of 1oz printed circuit board copper.
Parameter
DMAX
= (T
JMAX
- T
A
A
)/θ
= 25˚C.
JA
or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4854, see power derating
THD+N = 1.0%, f = 1kHz, R
THD+N = 10%, f = 1kHz, R
THD+N = 1.0%, f = 1kHz, R
THD+N = 10%, f = 1kHz, R
20Hz ≤ f
THD = 0.5%, R
f
f
P
IN
IN
O
R
= 1kHz, C
= 1kHz, C
= 30mW, R
L
= 32Ω, P
IN
= ≤ 20kHz
BYPASS
BYPASS
O
L
L
Conditions
= 30mW
= 32Ω
= 5kΩ
8
= 1.0µF, R
= 1.0µF
L
L
DD
L
L
= 32Ω
= 16Ω
= 32Ω
= 16Ω
L
= 3.0V)
= 32Ω
JMAX
, θ
JA
, and the ambient temperature, T
(Notes 4, 9)
(Note 8)
Typical
TBD
100
0.3
2.4
32
60
57
55
LM4854
(Notes 9,
Limit
10)
27
38
A
. The maximum
mW (min)
mW(min)
(Limits)
Units
V
mW
mW
dB
dB
%
P-P

Related parts for LM4854LD/NOPB