ISL54004IRTZ-T Intersil, ISL54004IRTZ-T Datasheet
![IC AMP AUDIO PWR 1.23W AB 20TQFN](/photos/28/17/281770/20-tqfn_l20_sml.jpg)
ISL54004IRTZ-T
Specifications of ISL54004IRTZ-T
Related parts for ISL54004IRTZ-T
ISL54004IRTZ-T Summary of contents
Page 1
... ISL54004 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2007. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL54004 FN6513 ...
Page 2
... PART PART RANGE NUMBER MARKING (°C) ISL54004IRTZ* 540 04IRTZ - 4x4 TQFN (Note) *Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials ...
Page 3
... Thermal Information Thermal Resistance (Typical, Note 4x4 TQFN Package . . . . . . . . . . Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Test Conditions +5V, GND = 0V 1µ terminated between SPK+ and SPK- for BTL driver and between Hp_ and ...
Page 4
Electrical Specifications - 5V Supply PARAMETER Total Harmonic Distortion + Noise THD Max Output Voltage Swing OUT L Signal to Noise Ratio, SNR R L Output Noise Weight filter ...
Page 5
Electrical Specifications - 3.6V Supply PARAMETER GENERAL Quiescent Supply Current coupled to GND (0.1µF) Shutdown Supply Current (BTL) and R (0.1µF) BTL AMPLIFIER DRIVER ...
Page 6
... LEFT AUDIO MICRO CONTROLLER Detailed Description The Intersil ISL54004 device is an integrated audio power amplifier system designed to provide quality audio, while requiring minimal external components. Low 0.4% THD+N ensures clean, low distortion amplification of the audio signals designed to operate from a single +2.7V to +5V power supply ...
Page 7
The “Typical Application Circuit and Block Diagram” for this device is provided on page 6. The “Truth Table” for the device is provided on page 2. DC Bias Voltage The ISL54004 has internal DC bias circuitry which DC offsets the ...
Page 8
Low Power Shutdown With a logic “1” at the SD control pin the device enters the low power shutdown state. When in shutdown the BTL and headphone amplifiers go into an high impedance state and I supply current is reduced ...
Page 9
Typical Performance Curves 10 5.00 BTL R = 8Ω 1kHz 2.00 1.00 0.50 0.20 0.10 0.05 0.02 0.01 10m 20m 50m 100m OUTPUT POWER (W) FIGURE 3. THD+N vs OUTPUT POWER 0.20 V ...
Page 10
Typical Performance Curves 32Ω 30mW O 0.20 0.10 0.05 0.02 0. 100 200 500 1k FREQUENCY (Hz) FIGURE 9. THD+N vs FREQUENCY 0. ...
Page 11
Typical Performance Curves 10 5. 32Ω 1kHz 1.00 0.50 0.20 0.10 0.05 0.02 0.01 10m 20m 30m 40m OUTPUT POWER (W) FIGURE 15. THD+N vs OUTPUT POWER 10.0 V ...
Page 12
Typical Performance Curves -20 - -24 BTL -26 - 200MV RIPPLE P-P -30 -32 -34 -36 -38 -40 -42 -44 -46 -48 -50 -52 -54 -56 -58 -60 -62 -64 -66 -68 -70 10 ...
Page 13
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...