FC400R1-29 Lineage Power, FC400R1-29 Datasheet
FC400R1-29
Available stocks
Related parts for FC400R1-29
FC400R1-29 Summary of contents
Page 1
... Description The FC400R1-29 Power Module is a dc-dc converter that operates over an input voltage range of 18 Vdc to 36 Vdc and provides a precisely regulated dc output. The outputs are fully isolated from the inputs, allowing versa- tile polarity configurations and grounding connections. The module has a maximum power rating of 400 typical full-load efficiency of 85% ...
Page 2
... Table 1. Input Specifications Parameter Operating Input Voltage Maximum Input Current ( 36V): I FC400R1-29 Inrush Transient Input Reflected-ripple Current, Peak-to-peak ( MHz, 12 µH source impedance; see Figure 8.) Input Ripple Rejection (120 Hz) Fusing Considerations CAUTION: This power module is not internally fused. An input line fuse must always be used. ...
Page 3
... I O Peak Deviation Settling Time (V < 10% of peak deviation Consult your sales representative or the factory. † These are manufacturing test limits. In some situations, results may differ. Lineage Power 18 Vdc to 36 Vdc Input, 28 Vdc Output; 400 W (continued) Symbol V O, set V O — ...
Page 4
... Min Typ Max 0 — 1.2 — — 1.0 — — 15 — — 50 — 100 150 — — — 0.5 60 — 102 30.9* — 37.0* — 0.40 — Lineage Power Unit pF MΩ Unit hours g (oz.) Unit µ set nom V V/A ...
Page 5
... The following figures provide typical characteristics for the power modules 1 13.8 18.22 22.64 27.06 INPUT VOLTAGE, V Figure 1. Typical FC400R1-29 Input Characteristics at Room Temperature Lineage Power 18 Vdc to 36 Vdc Input, 28 Vdc Output; 400 W Symbol — — — — — R pwr/good I pwr/good R pwr/good V pwr/good ...
Page 6
... 1.487 4.003 6.519 9.035 OUTPUT CURRENT, I Figure 3. Typical FC400R1-29 Efficiency vs. Output Current at Room Temperature TIME, T (0.5 µs/div) Note: See Figure 9 for test conditions. Figure 4. Typical FC400R1-29 Output Ripple Voltage at Room Temperature and Full Load Output 6 6 11.551 14.067 (A) O 1-0327 Note: Tested with a 1000 µF aluminum and a 1.0 µF ceramic capaci- tor across the load ...
Page 7
... April 02, 2008 Characteristic Curves (continued) TIME, t (20 ms/div) Note: Tested with a 1000 µF aluminum and a 1.0 µF ceramic capaci- tor across the load. Figure 7. Typical FC400R1-29 Start-Up Transient at Room Temperature Input Test Configurations TO OSCILLOSCOPE LTEST 12 μH Cs 220 μF ESR < 0.1 Ω ...
Page 8
... If not using the remote on/off feature, short the ON/OFF pin to V (–). I SENSE(+) SENSE(–) CASE I on/off ON/OFF + V (+) V I on/off – V (–) I Figure 11. Remote On/Off Implementation April 02, 2008 ). The switch can be generated by on/off = µA. V (+) O V (–) O 8-580 (F).d Lineage Power ...
Page 9
... I O CONTACT RESISTANCE Figure 12. Effective Circuit Configuration for Single-Module Remote-Sense Operation Lineage Power 18 Vdc to 36 Vdc Input, 28 Vdc Output; 400 W Output Voltage Set-Point Adjustment (Trim) Output voltage trim allows the user to increase or decrease the output voltage set point of a module. This ...
Page 10
... The CURRENT MON pin provides a dc voltage propor- tional to the dc output current of the module given in the Feature Specifications table. For example, on the FC400R1-29, the V/A ratio is set at 370 mV/A ± 10 °C case load current the voltage on the CURRENT MON pin is 3.33 V. The current monitor sig- nal is referenced to the SENSE(– ...
Page 11
... SENSE(–) pins to the (–) side of the power bus at the same point. Close proximity and directness are necessary for good noise immunity. Lineage Power 18 Vdc to 36 Vdc Input, 28 Vdc Output; 400 W When not using the parallel feature, leave the PARALLEL pin open ...
Page 12
... The output power of the module should not exceed the rated power of the module as listed in the Ordering Information table (+) (– MAXIMUM CASE TEMPERATURE (˚C) Figure 17. FC400R1-29 Max Case Temperature Using a Cold Plate 8-1303 (F).g April 02, 2008 100 105 110 1-0332 Lineage Power ...
Page 13
... The derating curve in Figure 17 was obtained from measurements obtained in experimental apparatus shown in Figure 18 MOUNTING SCREW LOCATION, 4 PLACES Lineage Power 18 Vdc to 36 Vdc Input, 28 Vdc Output; 400 W METAL BASE PLATE 0.060 INCH WIDE SLOT 0.030 INCH DEEP FOR THERMOCOUPLE PLACEMENT (SEE FIGURE 16 ...
Page 14
... For assistance with designing for EMC compliance, please refer to the FLTR100V10 Filter Module Data Sheet (DS99-294EPS). Layout Considerations Copper paths must not be routed beneath the power module mounting inserts. For additional layout guidelines, refer to the FLTR100V10 Filter Module Data Sheet (FDS01-043EPS). 14 (continued θcs θ – θ θ ------------------------ - – April 02, 2008 T A 8-1304 (F).e Lineage Power ...
Page 15
... MOUNTING INSERTS M3 x 0.5 THROUGH, 4 PLACES * Side label includes Lineage name, product designation, safety agency markings, input/output voltage and current ratings, and bar code. Lineage Power 18 Vdc to 36 Vdc Input, 28 Vdc Output; 400 W 116.8 (4.60) 1.02 (0.040) DIA SOLDER-PLATED, 9 PLACES 106 ...
Page 16
... Pin Length: 3.68 mm ± 0.25 mm (0.145 in. ± 0.010 in.) 16 2.54 (0.100) TYP 2.54 (0.100) TYP 106.68 (4.200) Output Device Power Code 400 W FC400R1-29 April 02, 2008 66.04 (2.600) 7.62 (0.300) 7.62 12.7 (0.300) (0.50) CASE 12.70 SYNC OUT 17.78 (0.500) (0.700) SYNC IN 22 ...
Page 17
... April 02, 2008 Notes Lineage Power 18 Vdc to 36 Vdc Input, 28 Vdc Output; 400 W 17 ...
Page 18
... No rights under any patent acc ompany the sale of any oduct information. © 2008 Lineage Power Corpor ation, (Mesquite, Texas ) All International Rights Res er ved. April 02, 2008 DS04-017 ver. 1.1 (Replaces: DS04-017 ver. 1.0 ) PDF name: fc400r1-29.pdf A sia-Pacific Head qu art ers T el: + 4283 dle-East an d Afric arters ...