X25F128S Xicor, X25F128S Datasheet

no-image

X25F128S

Manufacturer Part Number
X25F128S
Description
128K (16K x 8bit) SerialFlash memory with block lock protection
Manufacturer
Xicor
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
X25F128S
Manufacturer:
SHARP
Quantity:
6 226
FEATURES
• 1MHz Clock Rate
• SPI Serial Interface
• 16K X 8 Bits
• Low Power CMOS
• 1.8V – 3.6V or 5V “Univolt” Read and
• Block Lock Protection
• Built-in Inadvertent Program Protection
• Self-Timed Program Cycle
• High Reliability
• 8-Lead PDlP Package
• 16-Lead 150 mil SOIC Package
SerialFlash™ and Block Lock™ Protection are trademarks of Xicor, Inc.
© Xicor, Inc. 1995, 1996 Patents Pending
6829-1.9 4/7/97 T3/C0/D0 SH
X25F128
FUNCTIONAL DIAGRAM
— 32 Byte Small Sector Program Mode
— <1 A Standby Current
— <5mA Active Current
Program Power Supply Versions
— Protect 1/4, 1/2 or all of E
— Power-Up/Power-Down protection circuitry
— Program Enable Latch
— Program Protect Pin
— 5ms Program Cycle Time (Maximum)
— Endurance: 100,000 cycles per byte
— Data Retention: 100 Years
— ESD protection: 2000V on all pins
AN61 • AN75 • AN77 • AN79 • AN82
A V A I L A B L E
A
PPLICATION
SerialFlash™ Memory With Block Lock™ Protection
HOLD
SCK
CS
SO
PP
N
SI
OTE
2
AND CONTROL
PROM Array
COMMAND
DECODE
LOGIC
CONTROL LOGIC
PROGRAMMING
X25F128
REGISTER
DECODE
STATUS
LOGIC
X
1
DESCRIPTION
The X25F128 is a 131,072-bit CMOS SerialFlash
memory, internally organized 16K X 8. It features a
“Univolt” Program and Read voltage, Serial Peripheral
Interface (SPI), and software protocol allowing operation
on a simple three-wire bus. The bus signals are a clock
input (SCK), plus separate data in (SI) and data out (SO)
lines. Access to the device is controlled through a chip
select (CS) input, allowing any number of devices to
share the same bus.
The X25F128 also features two additional inputs that
provide the end user with added flexibility. By asserting
the HOLD input, the X25F128 will ignore transitions on
its inputs, thus allowing the host to service higher priority
interrupts. The PP input can be used as a hardwire input
to the X25F128 disabling all program attempts to the
status register, thus providing a mechanism for limiting
end user capability of altering 0, 1/4, 1/2, or all of the
memory.
The X25F128 utilizes Xicor’s proprietary flash cell, pro-
viding a minimum endurance of 100,000 cycles and a
minimum data retention of 100 years.
SECTOR DECODE LOGIC
32
DATA REGISTER
HIGH VOLTAGE
CONTROL
MEMORY
ARRAY
6829 ILL F01.1
Characteristics subject to change without notice
8
16K x 8 Bits

Related parts for X25F128S

X25F128S Summary of contents

Page 1

... SO COMMAND AND CONTROL SCK CS HOLD PP SerialFlash™ and Block Lock™ Protection are trademarks of Xicor, Inc. © Xicor, Inc. 1995, 1996 Patents Pending 6829-1.9 4/7/97 T3/C0/D0 SH X25F128 DESCRIPTION The X25F128 is a 131,072-bit CMOS SerialFlash memory, internally organized 16K features a “Univolt” Program and Read voltage, Serial Peripheral Interface (SPI), and software protocol allowing operation on a simple three-wire bus ...

Page 2

X25F128 PIN DESCRIPTIONS Serial Output (SO push-pull serial data output pin. During a read cycle, data is shifted out on this pin. Data is clocked out by the falling edge of the serial clock. Serial Input (SI) ...

Page 3

X25F128 PRINCIPLES OF OPERATION The X25F128 is a SerialFlash Memory designed to interface directly with the synchronous serial periph- eral interface (SPI) of many popular microcontroller families. The X25F128 contains an 8-bit instruction register accessed via the SI ...

Page 4

X25F128 Locked Unlocked PPEN PP PEL Blocks Blocks Locked Locked Locked Programmable Programmable 1 LOW 0 Locked Locked 1 LOW 1 Locked Programmable X HIGH 0 Locked Locked X HIGH 1 Locked Programmable Programmable ...

Page 5

X25F128 Operational Notes The device powers-up in the following state: • The device is in the low power standby state. • A HIGH to LOW transition required to enter an active state and receive an instruction. • ...

Page 6

X25F128 Figure 3. Program Enable Latch Sequence CS SCK INSTRUCTION HIGH IMPEDANCE 6 6829 ILL F05.1 ...

Page 7

X25F128 Figure 4. Programming Sequence SCK INSTRUCTION SCK DATA BYTE Figure 5. Program Status Register Operation Sequence CS ...

Page 8

X25F128 ABSOLUTE MAXIMUM RATINGS* Temperature Under Bias .................. – +135 C Storage Temperature ....................... – +150 C Voltage on any Pin with Respect to V D.C. Output Current ............................................. 5mA Lead Temperature (Soldering, 10 Seconds) ............................. ...

Page 9

X25F128 EQUIVALENT A.C. LOAD CIRCUIT 2.7V 1.64K 1.44K OUTPUT OUTPUT 4.63K 100pF 1.95K A.C. CHARACTERISTICS (Over recommended operating conditions, unless otherwise specified) Data Input Timing Symbol Parameter f Clock Frequency SCK t Cycle Time CYC CS Lead Time t LEAD ...

Page 10

X25F128 Serial Output Timing CS SCK MSB OUT ADDR SI LSB IN Serial Input Timing CS t LEAD SCK MSB IN HIGH IMPEDANCE CYC MSB–1 OUT t t ...

Page 11

X25F128 Hold Timing CS SCK SO SI HOLD 6829 ILL F12 11 ...

Page 12

X25F128 PACKAGING INFORMATION 8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL 0.015 (0.38) MAX. TYP. 0.010 (0.25) NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH ...

Page 13

X25F128 PACKAGING INFORMATION 16-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX PIN 1 (4X) 7 0.050 (1.27) 0.010 (0.25 0.020 (0.50) 0 – 8 0.016 (0.410) 0.037 (0.937) NOTE: ALL DIMENSIONS IN INCHES (IN ...

Page 14

... LIMITED WARRANTY Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. ...

Related keywords