X2816CSI-20 Xicor, X2816CSI-20 Datasheet
X2816CSI-20
Related parts for X2816CSI-20
X2816CSI-20 Summary of contents
Page 1
... Patents Pending 3852-1.4 3/27/96 T2/C3/D5 NS X2816C 2 PROM DESCRIPTION The Xicor X2816C advanced, high performance N-channel floating gate MOS technology. Like all Xicor Programmable nonvola- tile memories only device. The X2816C Control PP features the JEDEC approved pinout for byte-wide memories, compatible with industry standard RAMs, ROMs and EPROMs ...
Page 2
X2816C PIN DESCRIPTIONS Addresses (A – The Address inputs select an 8-bit memory location during a read or write operation. Chip Enable (CE) The Chip Enable input must be LOW to enable all read/write operations. When CE ...
Page 3
... HIGH during power-up and power-down, will inhibit inadvertent writes. Write cycle timing specifi- cations must be observed concurrently. ENDURANCE Xicor E 2 PROMs are designed and tested for applica- tions requiring extended endurance. 3 (i.e., write data = 0xxx 7 will reflect true data. ...
Page 4
X2816C SYSTEM CONSIDERATIONS Because the X2816C is frequently used in large memory arrays provided with a two line control architecture for both read and write operations. Proper usage can provide the lowest possible power dissipation and elimi- nate ...
Page 5
X2816C ABSOLUTE MAXIMUM RATINGS* Temperature under Bias X2816C ....................................... – +85 C X2816CI ..................................... – +135 C Storage Temperature ....................... – +150 C Voltage on any Pin with Respect to V .................................. –1V to ...
Page 6
X2816C ENDURANCE AND DATA RETENTION Parameter Minimum Endurance Data Retention POWER-UP TIMING Symbol PUR (3) t Power-Up to Read Operation PUW (3) t Power-Up to Write Operation CAPACITANCE 1MHz Symbol I/O (3) ...
Page 7
X2816C A.C. CHARACTERISTICS (Over recommended operating conditions unless otherwise specified.) Read Cycle Limits Symbol Parameter t Read Cycle Time RC t Chip Enable Access Time CE t Address Access Time AA t Output Enable Access Time OE CE LOW to ...
Page 8
X2816C Write Cycle Limits Symbol Parameter WC (5) t Write Cycle Time t Address Setup Time AS t Address Hold Time AH t Write Setup Time CS t Write Hold Time CH CE Pulse Width HIGH Setup ...
Page 9
X2816C CE Controlled Write Cycle ADDRESS OES DATA IN DATA OUT Page Mode Write Cycle ( (7) ADDR. * I/O BYTE 0 *For each successive write within ...
Page 10
X2816C DATA Polling Timing Diagram (10) ADDRESS I/O 7 Note: (10) Polling operations are by definition read cycles and are therefore subject to read cycle timings OEH D OUT =X t ...
Page 11
X2816C Normalized Active Supply Current vs. Ambient Temperature 1 1.2 1.0 0.8 0.6 –55 +25 AMBIENT TEMPERATURE ( C) Normalized Access Time vs. Ambient Temperature 1 1.2 1.0 0.8 0.6 –55 +25 ...
Page 12
X2816C PACKAGING INFORMATION 24-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P PIN 1 INDEX PIN 1 SEATING PLANE 0.150 (3.81) 0.125 (3.18) 0.110 (2.79) 0.090 (2.29) TYP. 0.010 (0.25) NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE ...
Page 13
X2816C PACKAGING INFORMATION 32-LEAD PLASTIC LEADED CHIP CARRIER PACKAGE TYPE J 0.420 (10.67) 0.045 (1.14 0.495 (12.57) 0.485 (12.32) TYP. 0.490 (12.45) 0.453 (11.51) 0.447 (11.35) TYP. 0.450 (11.43) 0.300 (7.62) REF. PIN 1 NOTES: 1. ALL DIMENSIONS ...
Page 14
X2816C PACKAGING INFORMATION 32-PAD CERAMIC LEADLESS CHIP CARRIER PACKAGE TYPE E 0.300 (7.62) 0.015 (0.38) 0.003 (0.08) PIN 1 0.200 (5.08) BSC 0.028 (0.71) 0.022 (0.56) (32) PLCS. 0.458 (11.63) 0.442 (11.22) 0.458 (11.63) NOTE: 1. ALL DIMENSIONS IN INCHES ...
Page 15
X2816C PACKAGING INFORMATION 24-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX PIN 1 (4X) 7 0.050 (1.27) 0.010 (0.25) 0.020 (0.50) 0 – 8 0.015 (0.40) 0.050 (1.27) NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN ...
Page 16
X2816C ORDERING INFORMATION Device X2816C Access Time –90 = 90ns –12 = 120ns –15 = 150ns –20 = 200ns Temperature Range Blank = Commercial = + Industrial = – ...