AD810ARZ Analog Devices Inc, AD810ARZ Datasheet - Page 3

• Manufacturer Part Number: AD810ARZ
• Description: IC CURR-FDBK AMP VIDEO LP 8-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD810ARZ

• Slew Rate: 1000 V/µs
• Applications: Current Feedback
• Number Of Circuits: 1
• -3db Bandwidth: 80MHz
• Current - Supply: 6.8mA
• Current - Output / Channel: 60mA
• Voltage - Supply, Single/dual (±): 5 V ~ 36 V, ±2.5 V ~ 18 V
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Gain Bandwidth: 80MHz
• Supply Voltage Range: ± 2.5V To ± 18V
• No. Of Amplifiers: 1
• Output Current: 60mA
• Amplifier Output: Single Ended
• Amplifier Type: Low Power, Video
• Bandwidth: 75 MHz
• Common Mode Rejection Ratio: 64
• Current, Input Bias: 2 μA (+Input), 0.7 μA (-Input)
• Current, Output: 60 mA
• Current, Supply: 8 mA
• Harmonic Distortion: -61 dBc
• Impedance, Thermal: 150 °C/W
• Package Type: SOIC-8
• Resistance, Input: 10 Megohms (+Input), 40 Ohms (-Input)
• Temperature, Operating, Range: -40 to +85 °C
• Voltage, Input: ±13 V (Common-Mode)
• Voltage, Noise: 2.9 nV/sqrt Hz
• Voltage, Offset: 1.5 mV
• Voltage, Output, High: +12.9 V
• Voltage, Output, Low: -12.9 V
• Voltage, Supply: ±15 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

ABSOLUTE MAXIMUM RATINGS
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V
Internal Power Dissipation
Output Short Circuit Duration . . . . Observe Derating Curves
Common-Mode Input Voltage . . . . . . . . . . . . . . . . . . . . . . V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Storage Temperature Range
Operating Temperature Range
Lead Temperature Range (Soldering 60 sec) . . . . . . . +300 C
NOTES
1
2
ESD SUSCEPTIBILITY
ESD (electrostatic discharge) sensitive device. Electrostatic
charges as high as 4000 volts, which readily accumulate on the
human body and on test equipment, can discharge without
detection. Although the AD810 features ESD protection
circuitry, permanent damage may still occur on these devices if
they are subjected to high energy electrostatic discharges.
Therefore, proper ESD precautions are recommended to avoid
any performance degradation or loss of functionality.
Model
AD810AN
AD810AR
AD810AR-REEL
5962-9313201MPA –55 C to +125 C 8-Pin Cerdip
REV. A
Parameter
Turn On Time
Turn Off Time
Disable Pin Current
Min Disable Pin Current to
POWER SUPPLY
NOTES
1
2
3
4
5
Specifications subject to change without notice.
Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational section of this specification is not implied. Exposure to absolute
maximum raring conditions for extended periods may affect device reliability.
8-Pin Plastic Package:
8-Pin SOIC Package:
See Analog Devices Military Data Sheet for 883B Specifications.
Slew rate measurement is based on 10% to 90% rise time with the amplifier configured for a gain of –10.
Voltage Swing is defined as useful operating range, not the saturation range.
Disable guaranteed break before make.
Turn On Time is defined with 5 V supplies using complementary output CMOS to drive the disable pin.
Disable
Operating Range
Quiescent Current
Power-Down Current
Plastic DIP . . . . . . . . . . . . . . . . . . . . . . . . –65 C to +125 C
Cerdip . . . . . . . . . . . . . . . . . . . . . . . . . . . –65 C to +150 C
Small Outline IC . . . . . . . . . . . . . . . . . . . –65 C to +125 C
AD810A . . . . . . . . . . . . . . . . . . . . . . . . . . . –40 C to +85 C
AD810S . . . . . . . . . . . . . . . . . . . . . . . . . . –55 C to +125 C
5
JA
JA
Temperature
Range
–40 C to +85 C
–40 C to +85 C
–40 C to +85 C
= 90 C/Watt; 8-Pin Cerdip Package:
= 150 C/Watt.
ORDERING GUIDE
2
. . . . . . . Observe Derating Curves
Conditions
Z
Z
Disable Pin = 0 V
T
+25 C to T
T
T
OUT
OUT
MIN
MIN
MIN
Package
Description
8-Pin Plastic DIP
8-Pin Plastic SOIC R-8
8-Pin Plastic SOIC R-8
–T
–T
1
= Low, See Figure 54
= High
MAX
MAX
MAX
JA
= 110 C/Watt;
Package
Option
N-8
Q-8
V
S
5 V
15 V
5 V, 15 V
5 V
15 V
5 V, 15 V
5 V
15 V
S
–3–
MAXIMUM POWER DISSIPATION
The maximum power that can be safely dissipated by the
AD810 is limited by the associated rise in junction temperature.
For the plastic packages, the maximum safe junction tempera-
ture is 145 C. For the cerdip package, the maximum junction
temperature is 175 C. If these maximums are exceeded momen-
tarily, proper circuit operation will be restored as soon as the die
temperature is reduced. Leaving the device in the “overheated”
condition for an extended period can result in device burnout.
To ensure proper operation, it is important to observe the
derating curves.
While the AD810 is internally short circuit protected, this may
not be sufficient to guarantee that the maximum junction
temperature is not exceeded under all conditions.
Maximum Power Dissipation vs. Temperature
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
–60
Min
2.5
3.0
–40
8-PIN
SOIC
AD810A
Offset Null Configuration
Typ
170
100
50
290
30
6.7
6.8
8.3
1.8
2.1
0.1µF
–20
8-PIN
MINI-DIP
AMBIENT TEMPERATURE –
0
Max
75
400
7.5
8.0
10.0
2.3
2.8
3
2
+V
18
18
AD810
7
S
20
–V
1
4
S
Min
40
10k
5
2.5
3.5
SEE TEXT
6
0.1µF
60
AD810S
Typ
100
50
290
30
6.7
6.8
9
1.8
2.1
8-PIN
CERDIP
170
80
°
C
1
100
Max
75
400
7.5
8.0
11.0
2.3
2.8
8-PIN
MINI-DIP
18
18
120
AD810
Units
ns
V
V
mA
mA
mA
mA
mA
ns
140
A
A
A