HA5023IBZ Intersil, HA5023IBZ Datasheet
HA5023IBZ
Specifications of HA5023IBZ
Available stocks
Related parts for HA5023IBZ
HA5023IBZ Summary of contents
Page 1
... HA5023IB96 5023I - HA5023IBZ 5023IBZ - (Note) HA5023IBZ96 5023IBZ - (Note) HA5023EVAL High Speed Op Amp DIP Evaluation Board *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets ...
Page 2
Absolute Maximum Ratings Voltage Between V+ and V- Terminals .36V DC Input Voltage (Note ...
Page 3
Electrical Specifications V SUPPLY PARAMETER -IN Common Mode Rejection -IN Power Supply Rejection Input Noise Voltage +Input Noise Current -Input Noise Current TRANSFER CHARACTERISTICS Transimpedence Open Loop DC Voltage Gain Open Loop DC Voltage Gain OUTPUT CHARACTERISTICS Output Voltage Swing ...
Page 4
Electrical Specifications V SUPPLY PARAMETER AC CHARACTERISTICS ( 681Ω Slew Rate Full Power Bandwidth Rise Time Fall Time Propagation Delay Overshoot -3dB Bandwidth Settling Time to 1% Settling Time to 0.25% Gain Flatness AC ...
Page 5
Test Circuits and Waveforms FIGURE 1. TEST CIRCUIT FOR TRANSIMPEDANCE MEASUREMENTS (NOTE 12) 100Ω DUT 50Ω 1kΩ F FIGURE 2. SMALL SIGNAL PULSE RESPONSE CIRCUIT NOTE: 12. A series input resistor of ≥100Ω is ...
Page 6
Schematic Diagram (One Amplifier of Two 800 2. 60K 800 800 V- ...
Page 7
Application Information Optimum Feedback Resistor The plots of inverting and non-inverting frequency response, see Figure 8 and Figure 9 in the typical performance section, illustrate the performance of the HA5023 in various closed loop gain configurations. Although the bandwidth dependency ...
Page 8
Typical Performance Curves 0.2V OUT P 10pF 681Ω 1kΩ 10, ...
Page 9
Typical Performance Curves 200 350 500 650 FEEDBACK RESISTOR (Ω) FIGURE 14. BANDWIDTH vs FEEDBACK RESISTANCE 0.10 0. 75Ω 150Ω L 0.04 0. 1kΩ L 0.00 3 ...
Page 10
Typical Performance Curves 8 100Ω 1.0V OUT P 7.5 7.0 6.5 6.0 -50 - TEMPERATURE (C) FIGURE 20. PROPAGATION DELAY vs TEMPERATURE 500 OUT P-P ...
Page 11
Typical Performance Curves 1.5 1.0 0.5 0.0 -60 -40 - TEMPERATURE (°C) FIGURE 26. INPUT OFFSET VOLTAGE vs TEMPERATURE -60 -40 - TEMPERATURE (°C) FIGURE 28. -INPUT BIAS ...
Page 12
Typical Performance Curves 40 +10V 30 + DISABLE INPUT VOLTAGE (V) FIGURE 32. SUPPLY CURRENT vs DISABLE INPUT VOLTAGE 0.01 0.10 LOAD RESISTANCE (kΩ) ...
Page 13
Typical Performance Curves DISABLE = P 750Ω F -10 -20 -30 -40 -50 -60 -70 -80 0.1 1 FREQUENCY (MHz) FIGURE 38. DISABLE FEEDTHROUGH vs FREQUENCY 13 HA5023 = ±5V ...
Page 14
Die Characteristics DIE DIMENSIONS: 1650µm x 2540µm x 483µm METALLIZATION: Type: Metal 1: AlCu (1%) ±0.4k Å Å Thickness: Metal 1: 8k Type: Metal 2: AlCu (1%) ±0.8k Å Å Thickness: Metal 2: 16k Metallization Mask Layout -IN1 +IN1 NC ...
Page 15
Dual-In-Line Plastic Packages (PDIP INDEX N/2 AREA -B- -A- D BASE PLANE -C- SEATING PLANE 0.010 (0.25 NOTES: 1. Controlling Dimensions: INCH. In case of conflict between ...
Page 16
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...