LT6551CMS Linear Technology, LT6551CMS Datasheet
LT6551CMS
Specifications of LT6551CMS
Available stocks
Related parts for LT6551CMS
LT6551CMS Summary of contents
Page 1
... Coaxial Cable Drivers ■ Low Voltage High Speed Signal Processing ■ Set Top Boxes , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. U TYPICAL APPLICATIO 3.3V Single Supply LT6551 RGB Plus SYNC Cable Driver LT6551 450Ω ...
Page 2
... Lead Temperature (Soldering, 10 sec).................. 300° OUT1 8 OUT2 7 OUT3 6 N/C ORDER PART NUMBER LTB9 LT6551CMS LT6551IMS LTC1 The ● denotes the specifications which apply over the specified = 25° 3.3V GND CONDITIONS No Load, V Ideal = 1.5V OUT Between Any Two Outputs Any Input ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are at T LT6551 (Pins 1,2,3,4 LT6550 (Pin 5), unless otherwise noted. EE PARAMETER Output Voltage Swing High PSRR Minimum Supply Voltage (Note 6) Output Short-Circuit Current Supply Current per ...
Page 4
LT6550/LT6551 5V ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are at T LT6551 (Pins 1,2,3,4 LT6550 (Pin 5), unless otherwise noted. EE PARAMETER PSRR Minimum Supply Voltage (Note 6) Output Short-Circuit Current Supply Current per Amplifier (Note 7) ...
Page 5
ELECTRICAL CHARACTERISTICS the specified temperature range, otherwise specifications are at T otherwise noted. PARAMETER Supply Current per Amplifier Slew Rate Small Signal –3dB Bandwidth Gain Flatness Gain Matching Settling Time to 3% Settling Time Overshoot Differential ...
Page 6
LT6550/LT6551 5V/3.3V TYPICAL PERFOR A CE CHARACTERISTICS V (Pin (LT6550), GND (Pin (LT6551) EE Input Bias Current vs Input Voltage 3.3V – 125°C A – ...
Page 7
TYPICAL PERFOR A CE CHARACTERISTICS V (Pin (LT6550), GND (Pin (LT6551) EE Frequency Response with Capacitive Loads 5V 2.5V DC OUT C = 150pF R ...
Page 8
LT6550/LT6551 5V/3.3V TYPICAL PERFOR A CE CHARACTERISTICS V (Pin (LT6550), GND (Pin (LT6551) EE ±5V TYPICAL PERFOR A CE CHARACTERISTICS V (Pin GND Supply Current vs Total Supply Voltage 14 V ...
Page 9
TYPICAL PERFOR A CE CHARACTERISTICS V (Pin GND Gain Flatness vs Frequency 6.2 = ± OUT R = 150Ω L 6.1 6.0 5.9 5.8 5.7 10k 100k 1M 10M 100M ...
Page 10
LT6550/LT6551 W BLOCK DIAGRA S LT6550 Block Diagram 450Ω 450Ω IN1 – 450Ω 450Ω IN2 – 450Ω 450Ω IN3 – GND OUT1 OUT2 OUT3 N/C GND 6550 BD01 LT6551 ...
Page 11
U U APPLICATIO S I FOR ATIO Amplifier Characteristics Figure 1 shows a simplified schematic of one channel of the LT6551 quad. Resistors RF and RG provide an internal gain of 2. (The LT6550 triple is a slight variation with ...
Page 12
LT6550/LT6551 U U APPLICATIO S I FOR ATIO Power Dissipation The LT6550/LT6551, enhanced θ Pin 5 (V for the LT6550 and GND for the LT6551) fused EE to the lead frame. This thermal connection increases the efficiency of the PC ...
Page 13
U TYPICAL APPLICATIO LUMINANCE CHROMA S Video Splitter LT6551 4k 470µF 450Ω 450Ω 75Ω 1k – 450Ω 450Ω 2 – 470µF 450Ω 450Ω 3 75Ω 1k – ...
Page 14
LT6550/LT6551 U TYPICAL APPLICATIO Consumer products require generation of YP nance/chrominance component signals, often from RGB source content. The YP P format has a luminance signal B R and two weighted color difference signals at baseband. Even with their fixed ...
Page 15
... LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... Shutdown, Operates to ±15V 800V/µs Slew Rate 0.1dB Gain Flatness to 150MHz, Shutdown 100MHz Pixel Switching, –3dB Bandwidth: 250MHz, 1100V/µs Slew Rate 350V/µs Slew Rate, Shutdown, Low Distortion –90dBc at 5MHz LT 1105 REV A • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2005 65501fa ...