HA5024IB Intersil, HA5024IB Datasheet - Page 2

• Manufacturer Part Number: HA5024IB
• Description: IC OPAMP QUAD 125MHZ 20-SOIC
• Manufacturer: Intersil

Specifications of HA5024IB

• Applications: Current Feedback
• Number Of Circuits: 4
• -3db Bandwidth: 125MHz
• Slew Rate: 350 V/µs
• Current - Supply: 7.5mA
• Current - Output / Channel: 20mA
• Voltage - Supply, Single/dual (±): ±4.5 V ~ 18 V
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (0.300", 7.50mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Absolute Maximum Ratings
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 36V
DC Input Voltage (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . ±V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10V
Output Current (Note 4) . . . . . . . . . . . . . . . . Short Circuit Protected
ESD Rating (Note 3)
Operating Conditions
Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
Supply Voltage Range (Typical) . . . . . . . . . . . . . . . . ±4.5V to ±15V
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
Electrical Specifications
INPUT CHARACTERISTICS
Input Offset Voltage (V
Delta V
Average Input Offset Voltage Drift
V
V
Input Common Mode Range
Non-Inverting Input (+IN) Current
+IN Common Mode Rejection
(+I
+IN Power Supply Rejection
Inverting Input (-IN) Current
Delta -IN BIAS Current Between Channels
-IN Common Mode Rejection
1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175°C for die, and below 150°C
2. θ
3. The non-inverting input of unused amplifiers must be connected to GND.
4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle)
Human Body Model (Per MIL-STD-883 Method 3015.7) . . .2000V
IO
IO
BCMR
for plastic packages. See Application Information section for safe operating area information.
output current should not exceed 15mA for maximum reliability.
Common Mode Rejection Ratio
Power Supply Rejection Ratio
JA
IO
is measured with the component mounted on an evaluation PC board in free air.
=
Between Channels
--------- -
R
1
IN
PARAMETER
)
IO
)
2
V
SUPPLY
= ±5V, R
Note 5
±3.5V ≤ V
Note 5
Note 5
±3.5V ≤ V
Note 5
TEST CONDITIONS
F
= 1kΩ, A
S
S
≤ ±6.5V
≤ ±6.5V
SUPPLY
V
= +1, R
HA5024
L
= 400Ω, C
Thermal Information
Thermal Resistance (Typical, Note 2)
Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . . 175°C
Maximum Junction Temperature (Plastic Package, Note 1) . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.
(NOTE 11)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(SOIC - Lead Tips Only)
LEVEL
TEST
A
A
A
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
L
≤ 10pF,Unless Otherwise Specified
TEMP.
25,85
25,85
(°C)
Full
Full
Full
Full
Full
Full
Full
Full
Full
-40
-40
Full
25
25
25
25
25
25
25
±2.5
MIN
53
50
60
55
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
TYP
0.8
1.2
10
10
5
3
4
6
-
-
-
-
-
-
-
-
-
-
-
-
-
MAX
0.15
3.5
0.5
0.1
0.3
0.4
1.0
20
12
30
15
30
3
5
8
-
-
-
-
-
-
February 8, 2006
θ
UNITS
JA
µV/°C
µA/V
µA/V
µA/V
µA/V
µA/V
µA/V
mV
mV
mV
dB
dB
dB
dB
µA
µA
µA
µA
µA
µA
V
(°C/W)
75
90
3550.6