AT32UC3A1256 Atmel Corporation, AT32UC3A1256 Datasheet - Page 138
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT32UC3A1256
Manufacturer Part Number
AT32UC3A1256
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(98 pages)
2.AT32UC3A0128.pdf
(826 pages)
3.AT32UC3A0128.pdf
(377 pages)
4.AT32UC3A0128.pdf
(33 pages)
5.AT32UC3A0128.pdf
(159 pages)
Specifications of AT32UC3A1256
Flash (kbytes)
256 Kbytes
Pin Count
100
Max. Operating Frequency
66 MHz
Cpu
32-bit AVR
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
69
Ext Interrupts
69
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device + OTG
Spi
6
Twi (i2c)
1
Uart
4
Ssc
1
Ethernet
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
16
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
64
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.0-3.6 or (1.65-1.95+3.0-3.6)
Operating Voltage (vcc)
3.0-3.6 or (1.65-1.95+3.0-3.6)
Fpu
No
Mpu / Mmu
Yes / No
Timers
10
Output Compare Channels
16
Input Capture Channels
6
Pwm Channels
13
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3A1256-U
Manufacturer:
ATMEL
Quantity:
496
9.8
9.8.1
9.8.1.1
32002F–03/2010
Memory Service Unit
CRC
Starting CRC calculation
The tool can read and write this register, although it is recommended that only the CPU writes
this register.
Table 9-53.
The Memory Service Unit (MSU) provides access to complex memory operations, such as CRC
checking and NanoTrace. The MSU is accessed by SAB registers, but these are not mapped
into the OCD register space, and needs to be accessed with MEMORY_WORD_ACCESS or
MEMORY_SERVICE_ACCESS JTAG commands. In addition the MSU registers are mapped in
the system register space and are available tothe CPU. Refer to
on page 11
The MSU can calculate a Cyclic Redundancy Check (CRC) value for a memory area. The algo-
rithm used is the industry standard CRC32 algorithm using the generator polynomial
0xEDB88320.
To calculate CRC for a memory range, you need to write the start address into the ADDRHI and
ADDRLO registers, and the size of the memory range into the LENGTH register. Both the start
address and the length must be word aligned.
The initial value used for the CRC calculation must be written to the DATA register. This value
will usually be 0xFFFFFFFF, but can be e.g. the result of a previous CRC calculation if generat-
ing a common CRC of separate memory blocks.
Once completed, the calculated CRC value can be read out of the DATA register. The read
value must be inverted to match standard CRC32 implementations, or kept non-inverted if used
as starting point for subsequent CRC calculations.
If the device has enabled protection features, e.g. the protection fuse has been set on devices
with onboard flash memory, it is only possible to calculate CRC on a predefined memory area. In
most cases this area will be the entire onboard flash memory. The ADDRHI, ADDRLO,
LENGTH, and DATA registers will be forced to predefined values once the CRC operation is
started, and user-written values are ignored. This allows the user to verify the contents of a pro-
tected device, while denying malicious users the option of analyzing the memory contents
through selective CRC calculations.
The actual test is started by writing OP_CRC to the CTRL register. A running CRC operation can
be cancelled by writing OP_IDLE to CTRL.
R/W
RW
Bit Number
31:0
for details.
Ownership Trace Process ID (PID)
Field Name
PROCESS
Init. Val.
0
Description
PROCESS - Process ID
The unique Process ID number of the currently
running process.
Section 2.5 ”System registers”
AVR32
138