AT89LP428 Atmel Corporation, AT89LP428 Datasheet - Page 78

• Manufacturer Part Number: AT89LP428
• Manufacturer: Atmel Corporation

Specifications of AT89LP428

• Flash (kbytes): 4 Kbytes
• Max. Operating Frequency: 25 MHz
• Cpu: 8051-1C
• Max I/o Pins: 30
• Spi: 1
• Uart: 1
• Sram (kbytes): 0.75
• Eeprom (bytes): 512
• Self Program Memory: IAP
• Operating Voltage (vcc): 2.4 to 5.5
• Timers: 3
• Isp: SPI/OCD
• Watchdog: Yes

Table 16-1.
Notes:
78
SCON Address = 98H
Bit Addressable
Bit
Symbol
FE
SM0
SM1
SM2
REN
TB8
RB8
TI
RI
(SMOD0 = 0/1)
1. SMOD0 is located at PCON.6.
2. f
AT89LP428/828
SM0/FE
osc
Function
Framing error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid
frames and must be cleared by software. The SMOD0 bit must be set to enable access to the FE bit. FE will be set
regardless of the state of SMOD0.
Serial Port Mode Bit 0, (SMOD0 must = 0 to access bit SM0)
Serial Port Mode Bit 1
Enables the Automatic Address Recognition feature in Modes 2 or 3. If SM2 = 1 then Rl will not be set unless the received
9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address. In Mode 1, if SM2 =
1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a Given or Broadcast Address.
In Mode 0, SM2 determines the idle state of the shift clock such that the clock is the inverse of SM2, i.e. when SM2 = 0
the clock idles high and when SM2 = 1 the clock idles low.
Enables serial reception. Set by software to enable reception. Clear by software to disable reception.
The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired. In Mode 0, setting TB8
enables Timer 1 as the shift clock generator.
In Modes 2 and 3, the 9th data bit that was received. In Mode 1, if SM2 = 0, RB8 is the stop bit that was received. In
Mode 0, RB8 is not used.
Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the beginning of the stop bit in the
other modes, in any serial transmission. Must be cleared by software.
Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or halfway through the stop bit time in the
other modes, in any serial reception (except see SM2). Must be cleared by software.
7
SCON – Serial Port Control Register
= oscillator frequency. The baud rate depends on SMOD1 (PCON.7).
SM0
0
0
1
1
(1)
interrupted by a data byte. An address byte, however, interrupts all slaves. Each slave can
examine the received byte and see if it is being addressed. The addressed slave clears its SM2
bit and prepares to receive the data bytes that follows. The slaves that are not addressed set
their SM2 bits and ignore the data bytes.
The SM2 bit can be used to check the validity of the stop bit in Mode 1. In a Mode 1 reception, if
SM2 = 1, the receive interrupt is not activated unless a valid stop bit is received.
SM1
SM1
6
0
1
0
1
Mode
0
1
2
3
SM2
5
Description
shift register
8-bit UART
9-bit UART
9-bit UART
REN
4
variable (Timer 1 or Timer 2)
variable (Timer 1 or Timer 2)
f
osc
TB8
/2 or f
3
f
osc
Baud Rate
/32 or f
osc
/4 or Timer 1
osc
(2)
/16
RB8
2
Reset Value = 0000 0000B
T1
1
3654A–MICRO–8/09
RI
0