AT90CAN32 Automotive Atmel Corporation, AT90CAN32 Automotive Datasheet - Page 190
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT90CAN32 Automotive
Manufacturer Part Number
AT90CAN32 Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(431 pages)
2.AT90CAN128_AUTOMOTIVE.pdf
(16 pages)
3.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
Specifications of AT90CAN32 Automotive
Flash (kbytes)
32 Kbytes
Pin Count
64
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
53
Ext Interrupts
8
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
2
Can
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 125
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
8
Input Capture Channels
2
Pwm Channels
7
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT90CAN128_AUTOMOTIVE PDF datasheet #2
- AT90CAN128_AUTOMOTIVE PDF datasheet #3
- Current page: 190 of 431
- Download datasheet (6Mb)
izontal arrows illustrate the synchronization variation due to the sampling process. Note the
larger time variation when using the Double Speed mode (U2Xn = 1) of operation. Samples
denoted zero are samples done when the RxDn line is idle (i.e., no communication activity).
Figure 17-5. Start Bit Sampling
When the clock recovery logic detects a high (idle) to low (start) transition on the RxDn line, the
start bit detection sequence is initiated. Let sample 1 denote the first zero-sample as shown in
the figure. The clock recovery logic then uses samples 8, 9, and 10 for Normal mode, and sam-
ples 4, 5, and 6 for Double Speed mode (indicated with sample numbers inside boxes on the
figure), to decide if a valid start bit is received. If two or more of these three samples have logical
high levels (the majority wins), the start bit is rejected as a noise spike and the Receiver starts
looking for the next high to low-transition. If however, a valid start bit is detected, the clock recov-
ery logic is synchronized and the data recovery can begin. The synchronization process is
repeated for each start bit.
17.9.2
Asynchronous Data Recovery
When the receiver clock is synchronized to the start bit, the data recovery can begin. The data
recovery unit uses a state machine that has 16 states for each bit in Normal mode and eight
states for each bit in Double Speed mode.
Figure 17-6
shows the sampling of the data bits and
the parity bit. Each of the samples is given a number that is equal to the state of the recovery
unit.
Figure 17-6. Sampling of Data and Parity Bit
The decision of the logic level of the received bit is taken by doing a majority voting of the logic
value to the three samples in the center of the received bit. The center samples are emphasized
on the figure by having the sample number inside boxes. The majority voting process is done as
follows: If two or all three samples have high levels, the received bit is registered to be a logic 1.
If two or all three samples have low levels, the received bit is registered to be a logic 0. This
majority voting process acts as a low pass filter for the incoming signal on the RxDn pin. The
recovery process is then repeated until a complete frame is received. Including the first stop bit.
Note that the Receiver only uses the first stop bit of a frame.
AT90CAN32/64/128
190
7682C–AUTO–04/08
Related parts for AT90CAN32 Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AT90CAN32-16AU](/photos/12/13/121332/313-64-tqfp_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 64-TQFP
Manufacturer:
Atmel
Datasheet:
![AT90CAN32-16MU](/photos/12/13/121326/313-64-qfn_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 64-QFN
Manufacturer:
Atmel
Datasheet:
![AT90CAN32](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![AT90CAN32-16AUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 32K FLASH 16MHZ 64-TQFP
Manufacturer:
Atmel
Datasheet:
![AT90CAN32-16AI](/images/no-image3.png)
Part Number:
Description:
Microcontroller with 32K/64K/128K Bytes of ISP Flash and CAN Controller
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![AT90CAN32-16MI](/images/no-image3.png)
Part Number:
Description:
8-bit Microcontroller with 16K/32K/64K Bytes In-System Programmable Flash8-bit Microcontroller with 32K/64K/128K Bytes of ISP Flash and CAN Controller
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet: