AT90PWM216 Atmel Corporation, AT90PWM216 Datasheet - Page 276
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT90PWM216
Manufacturer Part Number
AT90PWM216
Description
Manufacturer
Atmel Corporation
Specifications of AT90PWM216
Flash (kbytes)
16 Kbytes
Pin Count
24
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
19
Ext Interrupts
4
Usb Speed
No
Usb Interface
No
Spi
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
125
Analog Comparators
2
Resistive Touch Screen
No
Dac Channels
1
Dac Resolution (bits)
10
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 105
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
12
Input Capture Channels
1
Pwm Channels
7
32khz Rtc
No
Calibrated Rc Oscillator
Yes
- Current page: 276 of 361
- Download datasheet (5Mb)
24.7.7
24.7.8
24.7.9
7710F–AVR–09/11
Setting the Boot Loader Lock Bits by SPM
EEPROM Write Prevents Writing to SPMCSR
Reading the Fuse and Lock Bits from Software
the RWWSRE. See
example.
To set the Boot Loader Lock bits, write the desired data to R0, write “X0001001” to SPMCSR
and execute SPM within four clock cycles after writing SPMCSR. The only accessible Lock bits
are the Boot Lock bits that may prevent the Application and Boot Loader section from any soft-
ware update by the MCU.
See
Flash access.
If bits 5..2 in R0 are cleared (zero), the corresponding Boot Lock bit will be programmed if an
SPM instruction is executed within four cycles after BLBSET and SPMEN are set in SPMCSR.
The Z-pointer is don’t care during this operation, but for future compatibility it is recommended to
load the Z-pointer with 0x0001 (same as used for reading the lO
is also recommended to set bits 7, 6, 1, and 0 in R0 to “1” when writing the Lock bits. When pro-
gramming the Lock bits the entire Flash can be read during the operation.
Note that an EEPROM write operation will block all software programming to Flash. Reading the
Fuses and Lock bits from software will also be prevented during the EEPROM write operation. It
is recommended that the user checks the status bit (EEPE) in the EECR Register and verifies
that the bit is cleared before writing to the SPMCSR Register.
It is possible to read both the Fuse and Lock bits from software. To read the Lock bits, load the
Z-pointer with 0x0001 and set the BLBSET and SPMEN bits in SPMCSR. When an LPM instruc-
tion is executed within three CPU cycles after the BLBSET and SPMEN bits are set in SPMCSR,
the value of the Lock bits will be loaded in the destination register. The BLBSET and SPMEN
bits will auto-clear upon completion of reading the Lock bits or if no LPM instruction is executed
within three CPU cycles or no SPM instruction is executed within four CPU cycles. When BLB-
SET and SPMEN are cleared, LPM will work as described in the Instruction set Manual.
The algorithm for reading the Fuse Low byte is similar to the one described above for reading
the Lock bits. To read the Fuse Low byte, load the Z-pointer with 0x0000 and set the BLBSET
and SPMEN bits in SPMCSR. When an LPM instruction is executed within three cycles after the
BLBSET and SPMEN bits are set in the SPMCSR, the value of the Fuse Low byte (FLB) will be
loaded in the destination register as shown below. Refer to
detailed description and mapping of the Fuse Low byte.
Similarly, when reading the Fuse High byte, load 0x0003 in the Z-pointer. When an LPM instruc-
tion is executed within three cycles after the BLBSET and SPMEN bits are set in the SPMCSR,
Bit
R0
Bit
Rd
Bit
Rd
Table 24-2
FLB7
and
7
1
7
–
7
“Simple Assembly Code Example for a Boot Loader” on page 277
Table 24-3
FLB6
6
1
6
–
6
for how the different settings of the Boot Loader bits affect the
BLB12
BLB12
FLB5
5
5
5
BLB11
BLB11
FLB4
4
4
4
BLB02
BLB02
FLB3
3
3
3
AT90PWM216/316
BLB01
BLB01
FLB2
2
2
ck
2
Table 25-4 on page 282
bits). For future compatibility it
FLB1
LB2
1
1
1
1
FLB0
LB1
0
1
0
0
for an
for a
276
Related parts for AT90PWM216
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AT90-1107TR](/images/manufacturer_photos/0/4/405/m_a-com_technology_solutions_tmb.jpg)
Part Number:
Description:
Digital Attenuator 32-Pin FQFP T/R
Manufacturer:
M/A-Com Technology Solutions
Datasheet:
![AT90-1106](/images/manufacturer_photos/0/4/405/m_a-com_technology_solutions_tmb.jpg)
Part Number:
Description:
MLP DIGITAL ATTENUATOR
Manufacturer:
M/A-Com Technology Solutions
![AT90-1233](/images/manufacturer_photos/0/4/405/m_a-com_technology_solutions_tmb.jpg)
Part Number:
Description:
Digital Attenuator 32-Pin FQFP
Manufacturer:
M/A-Com Technology Solutions
Datasheet:
![AT90-1233TR](/images/manufacturer_photos/0/4/405/m_a-com_technology_solutions_tmb.jpg)
Part Number:
Description:
Digital Attenuator 32-Pin FQFP T/R
Manufacturer:
M/A-Com Technology Solutions
Datasheet:
![AT90-0263](/images/manufacturer_photos/0/4/405/m_a-com_technology_solutions_tmb.jpg)
Part Number:
Description:
MLP DIGITAL ATTENUATOR
Manufacturer:
M/A-Com Technology Solutions
![AT90-0106](/images/manufacturer_photos/0/6/687/tyco_electronics_tmb.jpg)
Part Number:
Description:
Digital Attenuator, 50 Db, 6-bit, Ttl Driver, Dc-2.4 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
![AT90-0107](/images/manufacturer_photos/0/6/687/tyco_electronics_tmb.jpg)
Part Number:
Description:
Digital Attenuator, 31.5 Db, 6-bit, Ttl Driver, Dc-4.0 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
![AT90-1107](/images/manufacturer_photos/0/6/687/tyco_electronics_tmb.jpg)
Part Number:
Description:
Digital Attenuator, 31.5 Db, 6-bit, Ttl Driver, Dc-4.0 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
![AT90-1263](/images/manufacturer_photos/0/6/687/tyco_electronics_tmb.jpg)
Part Number:
Description:
Digital Attenuator, 31db, 5-bit, Ttl Driver Dc - 3.0 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
![AT90-1283](/images/manufacturer_photos/0/6/687/tyco_electronics_tmb.jpg)
Part Number:
Description:
Digital Attenuator, 15.5 Db, 5-bit, Ttl Driver, Dc-3.5 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet: