ATmega328P Automotive Atmel Corporation, ATmega328P Automotive Datasheet - Page 58

• Manufacturer Part Number: ATmega328P Automotive
• Manufacturer: Atmel Corporation

Specifications of ATmega328P Automotive

• Flash (kbytes): 32 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

58
ATmega328P [Preliminary]
When the BOOTRST Fuse is unprogrammed, the Boot section size set to 2K bytes and the
IVSEL bit in the MCUCR Register is set before any interrupts are enabled, the most typical and
general program setup for the Reset and Interrupt Vector Addresses in ATmega328P is:
When the BOOTRST Fuse is programmed and the Boot section size set to 2K bytes, the most
typical and general program setup for the Reset and Interrupt Vector Addresses in
ATmega328P is:
When the BOOTRST Fuse is programmed, the Boot section size set to 2K bytes and the IVSEL
bit in the MCUCR Register is set before any interrupts are enabled, the most typical and general
program setup for the Reset and Interrupt Vector Addresses in ATmega328P is:
0x0035
0x0036
0x0037
0x0038
Address Labels Code
0x0000
0x0001
0x0002
0x0003
0x0004
0x0005
;
.org 0x3C02
0x3C02
0x3C04
...
0x3C32
Address Labels Code
.org 0x0002
0x0002
0x0004
...
0x0032
;
.org 0x3C00
0x3C00
0x3C01
0x3C02
0x3C03
0x3C04
0x3C05
Address Labels Code
;
.org 0x3C00
0x3C00
0x3C02
...
RESET: ldi
RESET: ldi
...
ldi
out
sei
<instr>
out
ldi
out
sei
<instr>
jmp
jmp
...
jmp
jmp
jmp
...
jmp
out
ldi
out
sei
<instr>
jmp
jmp
...
...
r16, low(RAMEND)
SPL,r16
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
EXT_INT0
EXT_INT1
...
SPM_RDY
EXT_INT0
EXT_INT1
...
SPM_RDY
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
RESET
EXT_INT0
xxx
xxx
xxx
Comments
; Enable interrupts
Comments
; Set Stack Pointer to top of RAM
; Enable interrupts
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program Memory Ready Handler
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
Comments
; Reset handler
; IRQ0 Handler
7810A–AVR–11/09