ATmega8 Atmel Corporation, ATmega8 Datasheet - Page 47

• Manufacturer Part Number: ATmega8
• Manufacturer: Atmel Corporation

Specifications of ATmega8

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 2
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

2486Z–AVR–02/11
Table 19. Reset and Interrupt Vectors Placement
Note:
The most typical and general program setup for the Reset and Interrupt Vector Addresses in
ATmega8 is:
BOOTRST
addressLabels Code
$000
$001
$002
$003
$004
$005
$006
$007
$008
$009
$00a
$00b
$00c
$00d
$00e
$00f
$010
$011
$012
;
$013
$014
$015
$016
$017
$018
...
1
1
0
0
1. The Boot Reset Address is shown in
(1)
means unprogrammed while “0” means programmed
RESET: ldi
IVSEL
0
1
0
1
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
out
ldi
out
sei
<instr>
...
Reset Address
0x000
0x000
Boot Reset Address
Boot Reset Address
RESET
EXT_INT0
EXT_INT1
TIM2_COMP
TIM2_OVF
TIM1_CAPT
TIM1_COMPA
TIM1_COMPB
TIM1_OVF
TIM0_OVF
SPI_STC
USART_RXC
USART_UDRE
USART_TXC
ADC
EE_RDY
ANA_COMP
TWSI
SPM_RDY
SPH,r16
r16,low(RAMEND)
SPL,r16
...
xxx
r16,high(RAMEND); Main program start
Comments
; Reset Handler
; IRQ0 Handler
; IRQ1 Handler
; Timer2 Compare Handler
; Timer2 Overflow Handler
; Timer1 Capture Handler
; Timer1 CompareA Handler
; Timer1 CompareB Handler
; Timer1 Overflow Handler
; Timer0 Overflow Handler
; SPI Transfer Complete Handler
; USART RX Complete Handler
; UDR Empty Handler
; USART TX Complete Handler
; ADC Conversion Complete Handler
; EEPROM Ready Handler
; Analog Comparator Handler
; Two-wire Serial Interface Handler
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
Table 82 on page
Interrupt Vectors Start Address
0x001
Boot Reset Address + 0x001
0x001
Boot Reset Address + 0x001
213. For the BOOTRST Fuse “1”
ATmega8(L)
47