ATtiny84 Atmel Corporation, ATtiny84 Datasheet - Page 131

• Manufacturer Part Number: ATtiny84
• Manufacturer: Atmel Corporation

Specifications of ATtiny84

• Flash (kbytes): 8 Kbytes
• Pin Count: 14
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 6
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 12
• Ext Interrupts: 12
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

15.2.2
15.2.3
8006K–AVR–10/10
ADCSRB – ADC Control and Status Register B
DIDR0 – Digital Input Disable Register 0
between the Analog Comparator and the input capture function exists. To make the comparator
trigger the Timer/Counter1 Input Capture inter-rupt, the ICIE1 bit in the Timer Interrupt Mask
Register (TIMSK1) must be set.
• Bits 1:0 – ACIS1, ACIS0: Analog Comparator Interrupt Mode Select
These bits determine which comparator events that trigger the Analog Comparator interrupt. The
different settings are shown in
Table 15-2.
When changing the ACIS1/ACIS0 bits, the Analog Comparator Interrupt must be disabled by
clearing its Interrupt Enable bit in the ACSR Register. Otherwise an interrupt can occur when the
bits are changed.
• Bit 6 – ACME: Analog Comparator Multiplexer Enable
When this bit is written logic one and the ADC is switched off (ADEN in ADCSRA is zero), the
ADC multiplexer selects the negative input to the Analog Comparator. When this bit is written
logic zero, AIN1 is applied to the negative input of the Analog Comparator. For a detailed
description of this bit, see
• Bits 2:1 – ADC2D, ADC1D: ADC 2/1 Digital input buffer disable
When this bit is written logic one, the digital input buffer on the AIN1/0 pin is disabled. The corre-
sponding PIN Register bit will always read as zero when this bit is set. When an analog signal is
applied to the AIN1/0 pin and the digital input from this pin is not needed, this bit should be writ-
ten logic one to reduce power consumption in the digital input buffer.
Bit
0x03 (0x23)
Read/Write
Initial Value
Bit
0x01 (0x21)
Read/Write
Initial Value
ACIS1
0
0
1
1
ACIS1/ACIS0 Settings
ADC7D
R/W
R/W
BIN
7
0
7
0
ACIS0
0
1
0
1
ADC6D
ACME
R/W
R/W
“Analog Comparator Multiplexed Input” on page
6
0
6
0
Interrupt Mode
Comparator Interrupt on Output Toggle.
Reserved
Comparator Interrupt on Falling Output Edge.
Comparator Interrupt on Rising Output Edge.
Table
ADC5D
R/W
5
0
R
5
–
0
15-2.
ADC4D
ADLAR
R/W
R/W
4
0
4
0
ADC3D
R/W
3
0
R
3
–
0
ADC2D
ADTS2
R/W
R/W
2
0
2
0
ATtiny24/44/84
ADC1D
ADTS1
R/W
R/W
1
0
1
0
129.
ADC0D
ADTS0
R/W
R/W
0
0
0
0
ADCSRB
DIDR0
131