SAM7X512 Atmel Corporation, SAM7X512 Datasheet - Page 132
SAM7X512
Manufacturer Part Number
SAM7X512
Description
Manufacturer
Atmel Corporation
Specifications of SAM7X512
Flash (kbytes)
512 Kbytes
Pin Count
100
Max. Operating Frequency
55 MHz
Cpu
ARM7TDMI
Hardware Qtouch Acquisition
No
Max I/o Pins
62
Ext Interrupts
62
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Twi (i2c)
1
Uart
3
Can
1
Ssc
1
Ethernet
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.3
Operating Voltage (vcc)
3.0 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 132 of 687
- Download datasheet (11Mb)
20.3.4.4
20.3.4.5
132
SAM7X512/256/128
Flash Lock Commands
Flash General-purpose NVM Commands
All lock bits must be deactivated before using the Full Erase command. This can be done by
using the CLB command.
Table 20-22. Full Erase Command
Lock bits can be set using WPL or EWPL commands. They can also be set by using the Set
Lock command (SLB). With this command, several lock bits can be activated at the same time.
Bit 0 of Bit Mask corresponds to the first lock bit and so on.
In the same way, the Clear Lock command (CLB) is used to clear lock bits. All the lock bits can
also be cleared by the EA command.
Table 20-23. Set and Clear Lock Bit Command
Lock bits can be read using Get Lock Bit command (GLB). When a bit set in the Bit Mask is
returned, then the corresponding lock bit is active.
Table 20-24. Get Lock Bit Command
General-purpose NVM bits (GP NVM) can be set with the Set GPNVM command (SGPB). Using
this command, several GP NVM bits can be activated at the same time. Bit 0 of Bit Mask corre-
sponds to the first GPNVM bit and so on.
In the same way, the Clear GPNVM command (CGPB) is used to clear GP NVM bits. All the
general-purpose NVM bits are also cleared by the EA command.
Table 20-25. Set and Clear General-purpose NVM Bit Command
GP NVM bits can be read using Get GPNVM Bit command (GGPB). When a bit set in the Bit
Mask is returned, then the corresponding GPNVM bit is set.
Table 20-26. Get General-purpose NVM Bit Command
Read/Write
Write
Read/Write
Write
Write
Read/Write
Write
Read
Read/Write
Write
Write
Read/Write
Write
Read
DR Data
EA
DR Data
SLB or CLB
DR Data
GLB
Bit Mask
Bit Mask
DR Data
SGPB or CGPB
Bit Mask
DR Data
GGPB
Bit Mask
6120I–ATARM–06-Apr-11
Related parts for SAM7X512
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: