SAM3N0A Atmel Corporation, SAM3N0A Datasheet - Page 346
SAM3N0A
Manufacturer Part Number
SAM3N0A
Description
Manufacturer
Atmel Corporation
- Current page: 346 of 752
- Download datasheet (17Mb)
24.11 Clock Failure Detector
The clock failure detector allows to monitor the 3 to 20 MHz Crystal or Ceramic Resonator-
based oscillator and to detect an eventual defect of this oscillator (for example if the crystal is
unconnected).
The clock failure detector can be enabled or disabled by means of the CFDEN bit in the PMC
Clock Generator Main Oscillator Register (CKGR_MOR). After reset, the detector is disabled.
However, if the 3 to 20 MHz Crystal or Ceramic Resonator-based Oscillator is disabled, the
clock failure detector is disabled too.
A failure is detected by means of a counter incrementing on the 3 to 20 MHzCrystal oscillator or
Ceramic Resonator-based oscillator clock edge and timing logic clocked on the slow clock RC
oscillator controlling the counter. The counter is cleared when the slow clock RC oscillator signal
is low and enabled when the slow clock RC oscillator is high. Thus the failure detection time is 1
slow clock RC oscillator clock period. If, during the high level period of slow clock RC oscillator,
less than 8 fast crystal clock periods have been counted, then a failure is declared.
If a failure of the 3 to 20 MHz Crystal or Ceramic Resonator-based oscillator clock is detected,
the CFDEV flag is set in the PMC Status Register (PMC_SR), and can generate an interrupt if it
is not masked. The interrupt remains active until a read operation in the PMC_SR register. The
user can know the status of the clock failure detector at any time by reading the CFDS bit in the
PMC_SR register.
If the 3 to 20 MHz Crystal or Ceramic Resonator-based oscillator clock is selected as the source
clock of MAINCK (MOSCSEL = 1), and if the Master Clock Source is PLLCK (CSS = 2), then a
clock failure detection switches automatically the Master Clock on MAINCK. Then whatever the
PMC configuration is, a clock failure detection switches automatically MAINCK on the 4/8/12
MHz Fast RC Oscillator clock. If the Fast RC oscillator is disabled when a clock failure detection
occurs, it is automatically re-enabled by the clock failure detection mechanism.
It takes 2 slow clock RC oscillator cycles to detect and switch from the 3 to 20 MHz Crystal or
Ceramic Resonator-based oscillator to the 4/8/12 MHz Fast RC Oscillator if the Master Clock
Source is Main Clock or 3 slow clock RC oscillator cycles if the Master Clock Source is PLL.
The user can know the status of the fault output at any time by reading the
bit in the
FOS
PMC_SR register.
SAM3N
346
11011A–ATARM–04-Oct-10
Related parts for SAM3N0A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Cortex M3 Flash Microcontroller Converges Performance and Simplicity
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: