CS6422-CSZ Cirrus Logic Inc, CS6422-CSZ Datasheet - Page 11

• Manufacturer Part Number: CS6422-CSZ
• Description: IC SPEAKERPHONE ENHANCED 20SOIC
• Manufacturer: Cirrus Logic Inc
• Type: Audio Processorr

Specifications of CS6422-CSZ

• Package / Case: 20-SOIC
• Applications: Speakerphones
• Mounting Type: Surface Mount
• Product: General Purpose Audio Amplifiers
• Available Set Gain: 34 dB
• Thd Plus Noise: 0.03 %
• Operating Supply Voltage: 5 V
• Supply Current: 10 mA, 50 mA
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Audio - Load Impedance: 10 KOhms
• Input Offset Voltage: 2.12 V
• Minimum Operating Temperature: 0 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Rohs Compliant: Yes
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: SOIC
• No. Of Pins: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 598-1200-5

of higher amplitude will clip the ADC input and
will result in poor echo canceller performance. See
Section 4., “Design Considerations” for more de-
tails.
The outputs are delta-sigma digital to analog con-
verters (DACs) and have similar requirements to
the ADCs. The DACs are pre-compensated to ex-
pect a single-pole RC filter with a corner frequency
at 4 kHz. The full scale voltage output from a DAC
is 1.1 V
ased around 2.12 VDC.
3.1.1
The pins API (pin 20), APO (pin 18), AO (pin 3),
and MB (pin 19) form the Acoustic Interface. A
block diagram of the Acoustic Interface is shown in
Figure 6.
API and APO are, respectively, the input and out-
put of the built-in microphone pre-amplifier. The
pre-amplifier is an inverting amplifier with a fixed
DS295F1
FAR-END
rms
NO
NI
Acoustic Interface
(3.1 V
(0,6,9.5,12 dB)
17
4
RGain
pp
) maximum, 1 V
ADC
DAC
rms
D
S
P
typical, bi-
Figure 6. Analog Interface
DAC
ADC
Transmit Path
Receive Path
CS6422
(0,6,9.5,12 dB)
gain of 34 dB biased around an input offset voltage
of 2.12 V. APO is the output of the pre-amplifier
after a 1 kΩ (typical) resistor. The circuitry con-
nected to the amplifier input must present low
source impedance (<100 Ω) to the API pin or the
gain will be reduced. When using the internal mic
preamp, a 0.022 µF capacitor should be placed be-
tween APO and ground to provide the anti-aliasing
filter required by the ADC, as shown in Figure 4.
The pre-amplifier may be bypassed by clearing the
‘Mic’ bit (Register 0, bit 15) using the Microcontrol-
ler Interface (see Section 3.2, “Microcontroller Inter-
face”). If the internal mic preamp is not used, a
0.022 µF capacitor should be tied between API and
ground, and APO should be driven directly. In this
case, the signal into APO must be low-pass filtered
by a single-pole RC filter with a corner frequency at
8 kHz (see Figure 5).
Following the pre-amplifier is a programmable an-
alog gain stage, called TGain, which is controlled
TGain
APO
18
Mic
1kΩ
Reference
Voltage
34 dB
MB
19
20
3
AO
API
CS6422
CS6422
NEAR-END
11
11