CS3308-CQZ Cirrus Logic Inc, CS3308-CQZ Datasheet - Page 25
![IC ANLG VOL CTRL 8CH DGTL 48LQFP](/photos/6/80/68083/cs3308-cqz_sml.jpg)
CS3308-CQZ
Manufacturer Part Number
CS3308-CQZ
Description
IC ANLG VOL CTRL 8CH DGTL 48LQFP
Manufacturer
Cirrus Logic Inc
Type
Controllerr
Datasheet
1.CS3308-CQZ.pdf
(44 pages)
Specifications of CS3308-CQZ
Package / Case
48-LQFP
Applications
High End Audio
Mounting Type
Surface Mount
Product
General Purpose Audio Amplifiers
Output Power
362 mW
Available Set Gain
22 dB
Thd Plus Noise
- 112 dB
Operating Supply Voltage
3.5 V / 5.25 V
Supply Current
36 mA
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Audio Load Resistance
2 KOhms
Input Offset Voltage
0.75 V
Input Signal Type
Single
Minimum Operating Temperature
- 10 C
Output Signal Type
Analog
Supply Voltage (max)
5.25 V
Supply Voltage (min)
3.1 V
Output Type
8-Channel Audio
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
598-1778 - EVALUATION BOARD FOR CS5376598-1496 - BOARD EVAL FOR CS3308 VOL CTRL
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
598-1598
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS3308-CQZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
DS702F1
input of device N+1 may be repeated for up to 128 devices per single CS signal. If more than 128 devices
are required in a system, separate CS signals may be used to create additional chains of up to 128 devices
per CS signal.
As each device is placed into reset (RESET is low), its ENOut signal is driven low. The ENOut signal will
continue to be driven low until the device is taken out of reset (RESET is high) and the Enable bit (see
able Next Device (Bit 0)” on page
To configure a unique Individual device address for each device on the shared serial bus, the first device
must be reset (a low to high transition on its RESET pin), the Individual device address register must be
written (using the CS3308’s default device address) with a unique device address, and the Enable bit must
be set to take the next device in the serial control chain out of reset. This process may be repeated until all
devices in the serial control chain have been assigned a new Individual device address.
grams this configuration process.
Notice that
discrete steps. While this demonstrates one approach to device configuration, it should be noted that two
steps are not necessary to complete the action of setting the Individual address and enabling the next de-
vice. This may be done simultaneously with one register write (containing the new Individual address and
the Enable bit set) to the Individual address register.
unique Individual chip adress
devices in a chain, setting a
This loop steps through the
Using the new Individual chip address,
for each device as it
perform a write cycle to set the Enable
progresses.
Figure 10
bit.
Figure 10. Individual Device Address Configuration Process
bringing the next device in the
ENout pin to be driven high,
shows the setting of the Individual address and the setting of the Enable bit as two
chain out of its reset state.
This will cause the device's
No
41) is set, at which time the ENOut signal will be driven high.
Optionally, device configuration (initial
etc.) may be implemented using the
Individual chip address register to a
perform a write cycle to change the
volume settings, Group addresses,
Using the default chip address,
new Individual device address.
chain been assigned a unique
Have all the devices in the
Reset the First Device
Apply System Power
chip address?
unique value.
in the Chain
Start
Yes
addressed with this new Individual device address.
device are set to their default value. The
ENout pin on each device is low, holding
each subsequent device in a reset state.
A device will also respond to register writes when
At this point, the chip addresses of each
addressed with its Group 1 or Group 2 address.
serial bus using the device's assigned
From this point forward, the device will only
independently adressed through the
respond to register reads and writes when
communicate with each device in parallel, but each
device will only respond when the first byte clocked
The Reset input pins of all devices in the chain are
in on the serial control bus matches its Individual,
clocked in does not match the one of the device's
Each device may now be
Group 1 or Group 2 address. If the first byte
unique chip address.
now high. The serial control interface will
chip addresses, the device will ignore all
subsequent traffic on the bus until a new
communication cycle is initiated.
Figure 10
CS3308
“En-
dia-
25