MAX13325GUI/V+T Maxim Integrated Products, MAX13325GUI/V+T Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX13325GUI/V+T
Manufacturer Part Number
MAX13325GUI/V+T
Description
IC AUD LINE DVR DL AUTO 28TSSOP
Manufacturer
Maxim Integrated Products
Type
Line Driver, Transmitterr
Datasheet
1.MAX13325GUIV.pdf
(21 pages)
Specifications of MAX13325GUI/V+T
Applications
Automotive Audio
Mounting Type
Surface Mount
Package / Case
28-TSSOP Exposed Pad, 28-eTSSOP, 28-HTSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Dual Automotive, Audio Line Drivers
with I
When in diagnostic mode, the MAX13325/MAX13326
detect if any of the differential outputs is shorted to
ground. Upon detection of the short to ground, the
faulted channel is switched off and its output goes into a
high-impedance state. The fault is reported using the I
interface and the FLAG output. See Table 12.
Table 12. Output Short to GND Diagnostic
Table 13. Overtemperature Diagnostic
14
Right-Channel Output
FAULT CONDITION
Left-Channel Output
FAULT CONDITION
Overtemperature
Overtemperature
_____________________________________________________________________________________
Short to GND
Short to GND
Shutdown
Warning
2
C Control and Diagnostic
Left channel switches off and output
TWARN bit is set in the GFAULT
TSHDN bit is set in the GFAULT
SGNDR bit is set in the RFAULT
SGNDL bit is set in the LFAULT
output goes to high-impedance
Left and right channels switch
Right channel switches off and
goes to high-impedance state.
off and output goes to high-
FLAG bit set. See Table 7.
FLAG bit set. See Table 7.
FLAG bit set. See Table 7.
FLAG bit set. See Table 7.
Register. See Table 4.
FLAG is asserted low.
FLAG is asserted low.
register. See Table 4.
FLAG is asserted low.
FLAG is asserted low.
register. See Table 5.
register. See Table 6.
STATUS REPORT
STATUS REPORT
impedance state.
Output Short to GND
state.
2
C
In GMASK register, set
In GMASK register, set
MTWARN bit to 1. See
MTSHDN bit to 1. See
In LMASK register, set
In RMASK register, set
Cannot be masked.
MSGNDR bit to 1. See
MSGNDL bit to 1. See
Cannot be masked.
Cannot be masked.
When in diagnostic mode, if the MAX13325/MAX13326
exceed the overtemperature warning or temperature shut-
down thresholds the device reports the condition using
the I
UNMASK
Table 8.
Table 8.
UNMASK
2
Table 10.
Table 9.
C interface and the FLAG output. See Table 13.
the RETRYL bit to 1 in the Command
Die temperature falls below warning
Left channel is enabled by setting
setting the RETRYR bit to 1 in the
Cleared on reading the GFAULT
Cleared on reading the GFAULT
RETRYR bit to 1 in the Command
RETRYL bit to 1 in the Command
Note: 500ms autoretry in stand-
Output is enabled by setting the
Cleared on reading the RFAULT
Output is enabled by setting the
Cleared on reading the LFAULT
Note: 500ms autoretry in stand-
Note: 500ms autoretry in stand-
Right channel is enabled by
Die temperature falls below
Byte register. See Table 3.
Byte register. See Table 3.
Command Byte register.
register. See Table 5.
register. See Table 6.
shutdown threshold.
Byte register.
RECOVERY
alone mode.
See Table 3.
RECOVERY
alone mode.
alone mode.
threshold.
register.
register.
Overtemperature