EP2AGX65DF25C5 Altera Corporation, EP2AGX65DF25C5 Datasheet - Page 15

• Manufacturer Part Number: EP2AGX65DF25C5
• Description: IC ARRIA II GX FPGA 65K 572FBGA
• Manufacturer: Altera Corporation
• Series: Arria II GXr

Specifications of EP2AGX65DF25C5

• Number Of Logic Elements/cells: 60214
• Number Of Labs/clbs: 2530
• Total Ram Bits: 5371904
• Number Of I /o: 252
• Number Of Gates: -
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 572-FBGA
• Lead Free Status: Contains lead
• Rohs Status: RoHS non-compliant

Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
Table 1–6. Recommended Operating Conditions for Arria II GZ Devices
December 2011 Altera Corporation
V
V
V
V
T
t
Notes to
(1) Altera recommends a 3.0-V nominal battery voltage when connecting V
(2) V
(3) n = 0, 1, or 2.
(4) V
(5) V
(6) Transceiver power supplies do not have power-on-reset (POR) circuitry. After initial power-up, violating the transceiver power supply operating
(3)
(3)
(3)
(3)
RAMP
J
CCL_GXBLn
CCL_GXBRn
CCH_GXBLn
CCH_GXBRn
Symbol
security key, you may connect the V
both, are configured at a base data rate > 4.25 Gbps. For data rates up to 4.25 Gbps, you can connect V
conditions could lead to unpredictable link behavior.
CCPD
CCA_L/R
CCH_GXBL/R
Table
must be 2.5 V when V
must be connected to a 3.0-V supply if the clock multiplier unit (CMU) phase-locked loop (PLL), receiver clock data recovery (CDR), or
Transceiver clock power (left side)
Transceiver clock power (right side)
Transmitter output buffer power (left side)
Transmitter output buffer power (right side)
Operating junction temperature
Power supply ramp time
1–6:
must be connected to a 1.5-V supply.
f
DC Characteristics
This section lists the supply current, I/O pin leakage current, on-chip termination
(OCT) accuracy and variation, input pin capacitance, internal weak pull-up and
pull-down resistance, hot socketing, and Schmitt trigger input specifications.
Supply Current
Standby current is the current the device draws after the device is configured with no
inputs or outputs toggling and no activity in the device. Because these currents vary
largely with the resources used, use the Microsoft Excel-based Early Power Estimator
(EPE) to get supply current estimates for your design.
For more information about power estimation tools, refer to the
Estimator User Guide
I/O Pin Leakage Current
Table 1–7
Table 1–7. I/O Pin Leakage Current for Arria II GX Devices
I
I
I
OZ
Symbol
CCIO
Description
is 2.5, 1.8, 1.5, or 1.2 V. V
CCBAT
lists the Arria II GX I/O pin leakage current specifications.
Input pin
Tri-stated I/O pin
to either GND or a 3.0-V power supply.
Description
and the
CCPD
PowerPlay Power Analysis
must be 3.0 V when V
V
V
I
O
Normal POR
(PORSEL=0)
(PORSEL=1)
= 0 V to V
Commercial
= 0 V to V
Condition
Industrial
Fast POR
CCBAT
Conditions
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
—
—
—
—
to a battery for volatile key backup. If you do not use the volatile
CCIOMAX
CCIOMAX
(Note 6)
CCIO
Minimum
is 3.0 V.
1.425
1.05
1.05
0.05
0.05
–40
0
(Part 2 of 2)
chapter.
Min
–10
–10
CCA_L/R
Typical
1.5
1.1
1.1
—
—
—
—
to either 3.0 V or 2.5 V.
(5)
PowerPlay Early Power
Typ
—
—
Maximum
1.575
Max
1.15
1.15
100
100
10
10
85
4
Unit
µA
µA
Unit
ms
ms
°C
°C
1–7
V
V
V