EP4SE530H40C3 Altera Corporation, EP4SE530H40C3 Datasheet - Page 39
![no-image](/images/manufacturer_photos/0/0/41/altera_corporation_sml.jpg)
EP4SE530H40C3
Manufacturer Part Number
EP4SE530H40C3
Description
IC STRATIX IV FPGA 530K 1517HBGA
Manufacturer
Altera Corporation
Series
STRATIX® IV Er
Datasheet
1.EP4SGX70DF29C4N.pdf
(80 pages)
Specifications of EP4SE530H40C3
Number Of Logic Elements/cells
531200
Number Of Labs/clbs
21248
Total Ram Bits
28033024
Number Of I /o
976
Number Of Gates
-
Voltage - Supply
0.87 V ~ 0.93 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
1517-BBGA Exposed Pad
Lead Free Status
Contains lead
Rohs Status
RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
EP4SE530H40C3ES
Manufacturer:
ALTERA
Quantity:
20 000
Company:
Part Number:
EP4SE530H40C3N
Manufacturer:
ALTERA
Quantity:
784
Part Number:
EP4SE530H40C3NES
Manufacturer:
ALTERA
Quantity:
20 000
Chapter 1: DC and Switching Characteristics for Stratix IV Devices
Switching Characteristics
Table 1–24. Transceiver Specifications for Stratix IV GT Devices (Part 8 of 8)
December 2011 Altera Corporation
Digital reset pulse
width
Notes to
(1) The minimum reconfig_clk frequency is 2.5 MHz if the transceiver channel is configured in Transmitter Only mode. The minimum reconfig_clk
(2) To calculate the REFCLK rms phase jitter requirement at reference clock frequencies other than 100 MHz, use the following formula: REFCLK rms phase
(3) Differential LVPECL signal levels must comply to the minimum and maximum peak-to-peak differential input voltage specified in this table.
(4) The device cannot tolerate prolonged operation at this absolute maximum.
(5) You must use the 1.2-V RXV
(6) The differential eye opening specification at the receiver input pins assumes that Receiver Equalization is disabled. If you enable Receiver
(7) The rate matcher supports only up to
(8) Time taken to rx_pll_locked goes high from rx_analogreset de-assertion. Refer to
(9) Time for which the CDR must be kept in lock-to-reference mode after rx_pll_locked goes high and before rx_locktodata is asserted in manual
(10) Time taken to recover valid data after the rx_locktodata signal is asserted in manual mode. Refer to
(11) Time taken to recover valid data after the rx_freqlocked signal goes high in automatic mode. Refer to
(12) A GPLL may be required to meet the PMA-FPGA fabric interface timing above certain data rates. For more information, refer to the "Left/Right PLL
(13) The Quartus II software automatically selects the appropriate slew rate depending on the configured data rate or functional mode.
(14) For applications that require low transmit lane-to-lane skew, use Basic (PMA Direct) xN to achieve PMA-Only bonding across all channels in the link.
(15) Pending Characterization.
(16) If your design uses more than one dynamic reconfiguration controller (altgx_reconfig) instances to control the transceiver (altgx) channels
Description
frequency is 37.5 MHz if the transceiver channel is configured in Receiver only or Receiver and Transmitter mode. For more information, refer to the
Dynamic Reconfiguration in Stratix IV Devices
jitter at f (MHz) = REFCLK rms phase jitter at 100 MHz * 100/f.
Equalization, the receiver circuitry can tolerate a lower minimum eye opening, depending on the equalization level. Use H-Spice simulation to derive
the minimum eye opening requirement with Receiver Equalization enabled.
mode. Refer to
Requirements in Basic (PMA Direct) Mode" section in the
You can bond all channels on one side of the device by configuring them in Basic (PMA Direct) xN mode. For more information about clocking
requirements in this mode, refer to the “Basic (PMA Direct) Mode Clocking” section in the
physically located on the same side of the device AND if you use different reconfig_clk sources for these altgx_reconfig instances, the delta
time between any two of these reconfig_clk sources becoming stable must not exceed the maximum specification listed.
Symbol/
Table
1–24:
Figure 1–2 on page
Conditions
ICM
—
setting if the input serial data standard is LVDS.
1–32.
±
300 ppm.
–1 Industrial Speed
Min
chapter.
Grade
Typ
Transceiver Clocking in Stratix IV Devices
Max
Minimum is two parallel clock cycles
Stratix IV Device Handbook Volume 4: Device Datasheet and Addendum
Min
–2 Industrial Speed
Typ
Grade
Figure 1–2 on page
Transceiver Clocking in Stratix IV Devices
Max
chapter.
Figure 1–2 on page
Figure 1–3 on page
Min
–3 Industrial Speed
1–32.
Typ
Grade
1–32.
Max
1–32.
chapter.
1–31
Unit
—