STM8L151G2 STMicroelectronics, STM8L151G2 Datasheet - Page 49
STM8L151G2
Manufacturer Part Number
STM8L151G2
Description
STM8L-Ultra Low Power-8 bits Microcontrollers
Manufacturer
STMicroelectronics
Datasheet
1.STM8L151G2.pdf
(111 pages)
Specifications of STM8L151G2
Operating Power Supply
1.65 to 3.6 V (without BOR), 1.8 to 3.6 V (with BOR)
Temperature Range
-40 to 85 or 125 °C
5 Low Power Modes
Wait, Low power run, Low power wait, Active-halt with RTC, Halt
Ultralow Leakage Per I/0
50 nA
Fast Wakeup From Halt
5 μs
Max Freq
16 MHz, 16 CISC MIPS peak
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STM8L151G2U6
Manufacturer:
STMicroelectronics
Quantity:
10 000
- Current page: 49 of 111
- Download datasheet (2Mb)
STM8L151x2, STM8L151x3
7
7.1
7.1.1
7.1.2
7.1.3
7.1.4
Electrical parameters
Parameter conditions
Unless otherwise specified, all voltages are referred to V
Minimum and maximum values
Unless otherwise specified the minimum and maximum values are guaranteed in the worst
conditions of ambient temperature, supply voltage and frequencies by tests in production on
100% of the devices with an ambient temperature at T
the selected temperature range).
Data based on characterization results, design simulation and/or technology characteristics
are indicated in the table footnotes and are not tested in production. Based on
characterization, the minimum and maximum values refer to sample tests and represent the
mean value plus or minus three times the standard deviation (mean±3Σ).
Typical values
Unless otherwise specified, typical data are based on T
only as design guidelines and are not tested.
Typical ADC1 accuracy values are determined by characterization of a batch of samples
from a standard diffusion lot over the full temperature range, where 95% of the devices have
an error less than or equal to the value indicated (mean±2Σ)
Typical curves
Unless otherwise specified, all typical curves are given only as design guidelines and are
not tested.
Loading capacitor
The loading conditions used for pin parameter measurement are shown in
Figure 9.
Pin loading conditions
Doc ID 018780 Rev 3
50 pF
STM8L PIN
A
A
= 25 °C and T
SS
= 25 °C, V
.
.
DD
Electrical parameters
A
= 3 V. They are given
= T
A
Figure
max (given by
9.
49/111
Related parts for STM8L151G2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STM8 touch sensing library
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER FOR STM8S207/8 SER
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
EVAL KIT TOUCH SENSING STM8S
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR STM8S
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD DAUGHTER FOR STM8S207/8
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
EVAL KIT MOTOR CONTROL STM8S
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Raisonance’s complete, low-cost starter kits for STM8 and ST7
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
EMULATOR FOR STM8
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools EvoPrimer Base MCU Target BRD w/Ext BRD
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools EvoPrimer Base Proto 5 Extention Boards
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet: