STM8L151K3 STMicroelectronics, STM8L151K3 Datasheet - Page 71
STM8L151K3
Manufacturer Part Number
STM8L151K3
Description
STM8L-Ultra Low Power-8 bits Microcontrollers
Manufacturer
STMicroelectronics
Datasheet
1.STM8L151G2.pdf
(111 pages)
Specifications of STM8L151K3
Operating Power Supply
1.65 to 3.6 V (without BOR), 1.8 to 3.6 V (with BOR)
Temperature Range
-40 to 85 or 125 °C
5 Low Power Modes
Wait, Low power run, Low power wait, Active-halt with RTC, Halt
Ultralow Leakage Per I/0
50 nA
Fast Wakeup From Halt
5 μs
Max Freq
16 MHz, 16 CISC MIPS peak
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
STM8L151x2, STM8L151x3
7.3.5
Table 32.
1. Data based on characterization results, not tested in production.
2. Conforming to JEDEC JESD22a117
3. The physical granularity of the memory is 4 bytes, so cycling is performed on 4 bytes even when a write/erase operation
4. Data based on characterization performed on the whole data memory.
Symbol
N
t
RET
V
t
I
RW
prog
prog
addresses a single byte.
DD
(2)
(3)
Operating voltage
(all modes, read/write/erase)
Programming time for 1 or 64 bytes (block)
erase/write cycles (on programmed byte)
Programming time for 1 to 64 bytes (block)
write cycles (on erased byte)
Programming/ erasing consumption
Data retention (program memory) after 10000
erase/write cycles at T
(3 and 6 suffix)
Data retention (program memory) after 10000
erase/write cycles at T
(3 suffix)
Data retention (data memory) after 300000
erase/write cycles at T
(3 and 6 suffix)
Data retention (data memory) after 300000
erase/write cycles at T
(3 suffix)
Erase/write cycles (program memory)
Erase/write cycles (data memory)
Flash program and data EEPROM memory
Memory characteristics
T
Table 31.
1. Minimum supply voltage without losing data stored in RAM (in Halt mode or under Reset) or in hardware
Flash memory
A
Symbol
= -40 to 125 °C unless otherwise specified.
V
registers (only in Halt mode). Guaranteed by characterization, not tested in production.
RM
RAM and hardware registers
Parameter
Data retention mode
A
A
A
A
= –40 to +85 °C
= –40 to +125 °C
= –40 to +85 °C
= –40 to +125 °C
Parameter
Doc ID 018780 Rev 3
(1)
Halt mode (or Reset)
T
T
A
A
T
T
=+25 °C, V
=+25 °C, V
T
f
A
A
SYSCLK
A
Conditions
T
T
(3 and 6 suffix),
T
T
= –40 to +105 °C
= –40 to +125 °C
RET
RET
= –40 to +85 °C
RET
RET
Conditions
(3 suffix) or
(3 suffix)
= +125 °C
= +125 °C
= +85 °C
= +85 °C
= 16 MHz
DD
DD
= 3.0 V
= 1.8 V
1.65
Min
300
30
30
10
1.65
Min
5
5
(4)
(1)
(1)
(1)
(1)
(1)
(1)
Electrical parameters
Typ
Typ
0.7
6
3
Max
Max
3.6
(1)
kcycles
years
Unit
71/111
Unit
mA
ms
ms
V
V