DS8007A Maxim, DS8007A Datasheet - Page 25
![no-image](/images/no-image-200.jpg)
DS8007A
Manufacturer Part Number
DS8007A
Description
The DS8007A multiprotocol dual smart card interface is an automotive grade, low-cost, dual smart card reader interface supporting all ISO 7816, EMV™, and GSM11-11 requirements
Manufacturer
Maxim
Datasheet
1.DS8007A.pdf
(41 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS8007A-EAG+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
DS8007A-EAG+T
Manufacturer:
Maxim Integrated
Quantity:
10 000
R = unrestricted read, W = unrestricted write, -n = value after reset, x = always reflects state of external device pin. This register is
reset to 0uuuxxxub on RIU = 0.
Note: A minimum of 2µs is needed between successive reads of the HSR to allow for hardware updates. In addition, a minimum of
2µs is needed between reads of the HSR and activation of card A, card B, or the AUX card.
Bit 7: Reserved.
Bit 6: Protection Card Interface B Status Bit
(PRTLB). This bit is set to 1 when a fault has been
detected on card reader interface B. A fault is defined
as detection of a short-circuit condition on either the
RSTB or V
I
while this bit is set. This bit returns to 0 after any HSR
read, unless the condition persists.
Bit 5: Protection Card Interface A Status Bit
(PRTLA). This bit is set to a 1 when a fault has been
detected on card reader interface A. A fault is defined
as detection of a short-circuit condition on either the
RSTA or V
I
while this bit is set. This bit returns to 0 after any HSR
read, unless the condition persists.
Bit 4: Supervisor Latch (SUPL). This bit is set to 1
when V
nally driving the DELAY pin < 1.25V. At this time the
INT signal is asserted at logic 0 (active). This bit returns
to 0 only after an HSR read outside the alarm pulse.
Address 0Fh
CC(SD)
CC(SD).
. The INT signal is asserted at logic 0 (active)
DD
The INT signal is asserted at logic 0 (active)
CCB
CCA
< V
RST
pin as given by DC specs I
pin as given by DC specs I
R-0
—
______________________________________________________________________________________
Multiprotocol Dual Smart Card Interface
7
or when a reset is caused by exter-
PRTLB
R-0
6
PRTLA
RST(SD)
RST(SD)
R-0
5
and
and
SUPL
R-1
4
Bit 3: Presence Latch B (PRLB). This bit is set to 1
when a level change has been detected on the PRESB
pin of card interface B. The INT signal is asserted at
logic 0 (active) while this bit is set. This bit returns to 0
after any HSR read.
Bit 2: Presence Latch A (PRLA). This bit is set to 1
when a level change has been detected on the PRESA
pin of card interface A. The INT signal is asserted at
logic 0 (active) while this bit is set. This bit returns to 0
after any HSR read.
Bit 1: INTAUX Latch (INTAUXL). This bit is set to 1
when a 0 → 1 or a 1 → 0 level change has been detect-
ed on the INTAUX pin. This bit remains set, regardless
of further level changes on the INTAUX pin until cleared
to 0 by any HSR read.
Bit 0: Protection Thermal Latch (PTL). This bit is set
to 1 when excessive heating (approximately +150°C or
greater) is detected. The INT signal is asserted at logic
0 (active) while this bit is set. This bit returns to 0 after
any HSR read, unless the condition persists.
Hardware Status Register (HSR)
PRLB
R-0
3
PRLA
R-0
2
INTAUXL
R-0
1
PTL
R-0
0
25