IR3553MTRPBF International Rectifier, IR3553MTRPBF Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/3/338/international_rectifier_sml.jpg)
IR3553MTRPBF
Manufacturer Part Number
IR3553MTRPBF
Description
The IR3553 integrated PowIRstage is a synchronous buck gate driver IC with co‐packed control and synchronous MOSFETs and Schottky diode.
Manufacturer
International Rectifier
Datasheet
1.IR3553MTRPBF.pdf
(22 pages)
Specifications of IR3553MTRPBF
Package
PQFN / 4 x 6
Iout (a)
40
Switch Freq (khz)
up to 1.0MHz
Input Range (v)
4.5 - 15
Output Range (v)
0.25 - (VCC -2.5)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IR3553MTRPBF
Manufacturer:
IR
Quantity:
4 300
Part Number:
IR3553MTRPBF
Manufacturer:
INFINEON/英飞凌
Quantity:
20 000
PIN DESCRIPTIONS
4, 12, 13
PIN #
14 – 16
6 – 11
5, 25
17
18
19
20
21
22
23
24
1
2
3
4
March 12, 2012 | FINAL DATASHEET
PIN NAME
PHSFLT#
BOOST
BBRK#
GATEL
CSIN+
PGND
REFIN
TGND
PWM
LGND
CSIN-
IOUT
VCC
VIN
SW
Inverting input to the current sense amplifier. Connect to LGND if the current sense
amplifier is not used.
Non-Inverting input to the current sense amplifier. Connect to LGND if the current sense
amplifier is not used.
Bias voltage for control logic. Connect a minimum 1uF cap between VCC and PGND (pin
4) if current sense amplifier is used. Connect a minimum 0.1uF cap between VCC and
PGND (pin 4) if current sense amplifier is not used.
Power ground of MOSFET driver and the synchronous MOSFET. MOSFET driver signal is
referenced to this pin.
Low-side MOSFET driver pins that can be connected to a test point in order to observe
the waveform.
Switch node of synchronous buck converter.
High current input voltage connection. Recommended operating range is 4.5V to 15V.
Connect at least two 10uF 1206 ceramic capacitors and a 0.1uF 0402 ceramic capacitor.
Place the capacitors as close as possible to VIN pins and PGND pins (12-13). The 0.1uF
0402 capacitor should be on the same side of the PCB as the IR3553.
Bootstrap capacitor connection. The bootstrap capacitor provides the charge to turn on
the control MOSFET. Connect a minimum 0.22µF capacitor from BOOST to SW pin. Place
the capacitor as close to BOOST pin as possible and minimize the parasitic inductance of
the connection from the capacitor to SW pin.
Open drain output of the phase fault circuits. Connect to an external pull-up resistor.
Output is low when a MOSFET fault or over temperature condition is detected.
3.3V logic level tri-state PWM input and 7V tolerant. “High” turns the control MOSFET
on, and “Low” turns the synchronous MOSFET on. “Tri-state” turns both MOSFETs off in
Body-Braking® mode. In diode emulation mode, “Tri-state” activates internal diode
emulation control. See “PWM Tri-state Input” Section for further details about the PWM
Tri-State functions.
3.3V logic level input and 7V tolerant with internal weak pull-up to 3.3V. Logic low
disables both MOSFETs. Pull up to VCC if Body-Braking
at least 20ns after VCC passes its UVLO threshold selects internal diode emulation
control. See “Body-Braking
Signal ground. Driver control logic, analog circuits and IC substrate are referenced to
this pin.
Reference voltage input from the PWM controller. IOUT signal is referenced to the
voltage on this pin. Connect to LGND if the current sense amplifier is not used.
Current output signal. Voltage on this pin is equal to V(REFIN) + 32.5 * [V(CSIN+) –
V(CSIN-)]. Float this pin if the current sense amplifier is not used.
This pin is connected to internal power and signal ground of the driver. For best
performance of the current sense amplifier, TGND must be electrically isolated from
Power Ground (PGND) and Signal Ground (LGND) in the PCB layout.
40A Integrated PowIRstage®
®
Mode” Section for further details.
PIN DESCRIPTION
®
is not used. Pulling BBRK# low
IR3553