7MBP75RJ120 Fuji Electric holdings CO.,Ltd, 7MBP75RJ120 Datasheet
7MBP75RJ120
Available stocks
Related parts for 7MBP75RJ120
7MBP75RJ120 Summary of contents
Page 1
SPECIFICATION Device Name : Type Name : Spec. No. : K.Sekigawa Sep. 17 '02 Nishiura T.Fujihira Sep. 17 '02 K.Yamada Sep.-17 -'02 IGBT - IPM 7MBP75RTB060 MS6M 0653 Fuji Electric Co.,Ltd. Matsumoto Factory MS6M 0653 H04-004-07 ...
Page 2
Classi- Date fication Ind. enactment Sep.-17-'02 a Apr.-09-'03 Revision Applied Content date Issued date Reliability Test Items. Apr.-09-'03 MS6M 0653 Drawn Checked Approved Nishiura K.Sekigawa T.Fujihira ...
Page 3
Outline Drawing ( Unit : mm ) Package type : P610 6- ...
Page 4
Descriptions Main circuit Symbol P Positive input supply voltage. U Output (U). V Output (V). W Output (W). N Negative input supply voltage. B Collector terminal of Brake IGBT. Control circuit № Symbol ① GNDU High side ground (U). ...
Page 5
Block Diagram VccU VccU 3 3 VinU VinU VinU GNDU GNDU GNDU 1 1 VccV VccV VinV VinV VinV ...
Page 6
Maximum Ratings Tc＝25℃ unless otherwise specified. Items Bus Voltage (between terminal P and N) Collector-Emitter Voltage *1 Collector Current Collector Power Dissipation Collector Current Forward Current of Diode Collector Power Dissipation Supply Voltage of Pre-Driver *4 Input Signal Voltage ...
Page 7
Electrical Characteristics Tj ＝ 25 ℃， Vcc ＝ 15V unless otherwise specified. 5.1 Main circuit Item Collector Current at off signal input Collector-Emitter saturation voltage Forward voltage of FWD Collector Current at off signal input Collector-Emitter saturation voltage Forward ...
Page 8
Protection Section （Vcc＝１５Ｖ） Item Over Current Protection Level of Inverter circuit Over Current Protection Level of Brake circuit Over Current Protection Delay time SC Protection Delay time IGBT Chips Over Heating Protection Temperature Level Over Heating Protection Hysteresis Over ...
Page 9
Figure 1. Switching Time Waveform Definitions /Vin on Gate On Vge (Inside IPM) Fault (Inside IPM) normal /ALM Figure 2. Input/Output Timing Diagram Necessary conditions for alarm reset (refer to ① to ③ in figure2.) ① This ...
Page 10
ALM ALM Figure.4 Definition of tsc VccU 20k IPM DC VinU 15V SW1 GNDU Vcc 20k DC VinX 15V SW2 GND Earth Figure 5. Noise Test Circuit Vcc Vcc 20k 20k DC DC Vin Vin 15V ...
Page 11
Truth table 10.1 IGBT Control The following table shows the IGBT ON/OFF status with respect to the input signal Vin. The IGBT turn-on when Vin is at “Low” level under no alarm condition. 10.2 Fault Detection (1) When a ...
Page 12
Cautions for design and application 1. Trace routing layout should be designed with particular attention to least stray capacity between the primary and secondary sides of optical isolators by minimizing the wiring length between the optical isolators and the ...
Page 13
Taking the used isolator’s CTR into account, design with a sufficient allowance to decide the primary forward current of the optical isolator. フォトカプラの一次側電流は、お使いのフォトカプラのCTRを考慮し十分に余裕をもった設計にして下さい。 11. Apply thermal compound to the surfaces between the IPM and its heat sink to reduce ...
Page 14
Example of applied circuit 応用回路例 20kΩ Vcc 20kΩ Vcc 20kΩ Vcc 20kΩ Vcc 20kΩ 20kΩ 20kΩ 13. Package and Marking 梱包仕様 Please see the MT6M4140 ...
Page 15
...
Page 16
...
Page 17
...
Page 18
...
Page 19
...
Page 20
Test Items １８． １８． Reliability Test Items Reliability Test Items Reliability Test Items Test cate- Test items gories 1 Terminal strength Pull force 端子強度 (Pull test) Test time 2 Mounting Strength Screw torque Test time 締付け強度 3 Vibration ...
Page 21
Test cate- Test items gories 1 High temperature Test temp. reverse bias Bias Voltage 高温逆ﾊﾞｲｱｽ Bias Method Test duration 2 Temperature Test temp. humidity bias Relative humidity Bias Voltage 高温高湿ﾊﾞｲｱｽ Bias Method Test duration 3 Intermitted ON time operating ...
Page 22
This product shall be used within its absolute maximum rating (voltage, current, and temperature). This product may be broken in case of using beyond the ratings. 製品の絶対最大定格（電圧，電流，温度等）の範囲内で御使用下さい。絶対最大定格を超えて使用すると、素子が 破壊する場合があります。 2. Connect adequate fuse or protector of circuit between three-phase line ...
Page 23
According to the outline drawing, select proper length of screw for main terminal. Longer screws may break the case. 本製品に使用する主端子用のネジの長さは、外形図に従い正しく選定下さい。ネジが長いとケースが破損する場合が あります。 excessive static electricity is applied to the control terminals, the devices can be broken. Implement some ...