PIC16F747 Microchip Technology Inc., PIC16F747 Datasheet - Page 44
PIC16F747
Manufacturer Part Number
PIC16F747
Description
28/40/44-pin, 8-bit Cmos Flash Microcontrollers With 10-bit A/d And Nanowatt Technology
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC16F747.pdf
(276 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F747-E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC16F747-I/ML
Manufacturer:
MICRON
Quantity:
1 001
Company:
Part Number:
PIC16F747-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC16F747-I/PT
Manufacturer:
MICROCH
Quantity:
20 000
Company:
Part Number:
PIC16F747T-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
- Current page: 44 of 276
- Download datasheet (6Mb)
PIC16F7X7
4.7.2
The core and peripherals can be configured to be
clocked by T1OSC using a 32.768 kHz crystal. The
crystal must be connected to the T1OSO and T1OSI
pins. This is the same configuration as the low-power
timer circuit (see Section 7.6 “Timer1 Oscillator”).
When SCS bits are configured to run from T1OSC, a
clock transition is generated. It will clear the OSTS bit,
switch the system clock from either the primary system
clock or INTRC, depending on the value of SCS<1:0>
and FOSC<2:0>, to the external low-power Timer1
oscillator input (T1OSC) and shut-down the primary
system clock to conserve power.
After a clock switch has been executed, the internal Q
clocks are held in the Q1 state until eight falling edge
clocks are counted on the T1OSC. After the eight clock
periods have transpired, the clock input to the Q clocks
is released and operation resumes (see Figure 4-8). In
addition, T1RUN (in T1CON) is set to indicate that
T1OSC is being used as the system clock.
FIGURE 4-8:
DS30498C-page 42
SCS<1:0>
Note 1:
Program
Counter
System
T1OSI
OSC1
Clock
2:
3:
4:
T
T
T
T
OSC
SCS
T
DLY
Q1
SEC_RUN MODE
1
T
P
OSC (2)
= 8 T
= 1 T
Q2
= 30.52 s.
= 50 ns minimum.
PC
Q3
T
T
1
1
P
P
.
Q4
TIMING DIAGRAM FOR SWITCHING TO SEC_RUN MODE
Q1
T
DLY
(4)
T
T
1
P
(1)
T
SCS (3)
PC + 1
Note 1: The T1OSCEN bit must be enabled and it
Q1
2: When T1OSCEN = 0, the following
Q2
A clock switching event will occur if the
final state of the SCS bits is different from
the original.
is the user’s responsibility to ensure
T1OSC is stable before clock switching to
the T1OSC input clock can occur.
possible effects result.
SCS<1:0>
Original
00
00
10
10
Q3
Q4
2004 Microchip Technology Inc.
SCS<1:0>
Modified
Q1
01
11
11
01
Q2
PC + 2
00 – no change
10 – INTRC
10 – no change
00 – Oscillator
defined by
FOSC<2:0>
Q3
SCS<1:0>
Final
Q4
PC + 3
Q1
Related parts for PIC16F747
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Photo IC(photodiode with signal processing)
Manufacturer:
KODENSHI KOREA CORP
Datasheet:
Part Number:
Description:
INFRARED RECEIVER MODULE
Manufacturer:
ETC
Datasheet:
Part Number:
Description:
INFRARED RECEIVER MODULE
Manufacturer:
ETC
Datasheet:
Part Number:
Description:
Photo IC(photodiode with signal processing)
Manufacturer:
KODENSHI KOREA CORP
Datasheet:
Part Number:
Description:
(PIC-1204x) OPTICAL-RECEIVER OUTPUT PHOTO IC
Manufacturer:
Kodenshi
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: