PIC16F819 Microchip Technology Inc., PIC16F819 Datasheet - Page 83

• Manufacturer Part Number: PIC16F819
• Description: 18/20-pin Enhanced Flash Microcontrollers With Nanowatt Technology
• Manufacturer: Microchip Technology Inc.

11.0
The Analog-to-Digital (A/D) converter module has five
inputs for 18/20 pin devices.
The conversion of an analog input signal results in a
corresponding 10-bit digital number. The A/D module
has a high and low-voltage reference input that is
software selectable to some combination of V
RA2 or RA3.
The A/D converter has a unique feature of being able
to operate while the device is in Sleep mode. To oper-
ate in Sleep, the A/D conversion clock must be derived
from the A/D’s internal RC oscillator.
REGISTER 11-1:
 2003 Microchip Technology Inc.
ANALOG-TO-DIGITAL
CONVERTER (A/D) MODULE
bit 7-6
bit 5-3
bit 2
bit 1
bit 0
ADCON0: A/D CONTROL REGISTER 0 (ADDRESS 1Fh)
ADCS1:ADCS0: A/D Conversion Clock Select bits
If ADCS2 = 0:
00 = F
01 = F
10 = F
11 = F
If ADCS2 = 1:
00 = F
01 = F
10 = F
11 = F
CHS2:CHS0: Analog Channel Select bits
000 = Channel 0 (RA0/AN0)
001 = Channel 1 (RA1/AN1)
010 = Channel 2 (RA2/AN2)
011 = Channel 3 (RA3/AN3)
100 = Channel 4 (RA4/AN4)
GO/DONE: A/D Conversion Status bit
If ADON = 1:
1 = A/D conversion in progress (setting this bit starts the A/D conversion)
0 = A/D conversion not in progress (this bit is automatically cleared by hardware when the
Unimplemented: Read as ‘0’
ADON: A/D On bit
1 = A/D converter module is operating
0 = A/D converter module is shut-off and consumes no operating current
bit 7
Legend:
R = Readable bit
-n = Value at POR
ADCS1
R/W-0
A/D conversion is complete)
OSC
OSC
OSC
RC
OSC
OSC
OSC
RC
(clock derived from the internal A/D module RC oscillator)
(clock derived from the internal A/D module RC oscillator)
/2
/8
/32
/4
/16
/64
ADCS0
R/W-0
DD
, V
R/W-0
CHS2
SS
W = Writable bit
‘1’ = Bit is set
,
R/W-0
CHS1
The A/D module has four registers:
• A/D Result High Register (ADRESH)
• A/D Result Low Register (ADRESL)
• A/D Control Register 0 (ADCON0)
• A/D Control Register 1 (ADCON1)
The ADCON0 register, shown in Register 11-1,
controls the operation of the A/D module. The
ADCON1 register, shown in Register 11-2, configures
the functions of the port pins. The port pins can be
configured as analog inputs (RA3 can also be a voltage
reference) or as digital I/Os.
Additional information on using the A/D module can be
found in the “PICmicro
Reference Manual” (DS33023).
R/W-0
CHS0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
PIC16F818/819
GO/DONE
R/W-0
®
Mid-Range MCU Family
x = Bit is unknown
DS39598D-page 81
U-0
—
ADON
R/W-0
bit 0