IHD215 CT-Concept Technologie AG, IHD215 Datasheet
IHD215
Related parts for IHD215
IHD215 Summary of contents
Page 1
Intelligent Half-Bridge Drivers for IGBTs and Power MOSFETs Description The intelligent half-bridge drivers of the IHD type series have been developed specifically for the reli- able driving and secure protection of IGBT or power-MOSFET pairs. All intelligent drivers of the ...
Page 2
IHD 215/280/680 Data Sheet & Application Manual Absolute Maximum Ratings Parameter Supply voltage V cc Gate peak current I out Test voltage (50Hz/1min) Operating temperature Storage temperature Pin Designation Pin Desig. Function 1 SO1+ Status output + (CH.1) 2 SO1- ...
Page 3
Block and Connection Diagram IHD 215/280/680 Data Sheet & Application Manual Page ...
Page 4
IHD 215/280/680 Data Sheet & Application Manual Mechanical Dimensions Layout overview (component side) Case & Coating Component Case product Coating mass Page Grid Solder pads Drill holes All dimensions are ...
Page 5
... General Characteristics Quality Manufacturing Reliability MTBF IHD215/280xx MTBF IHD680xx Thermal Characteristics Operating temperature Storage temperature Electrical Characteristics Power Supply Supply voltage V cc (see Note 1) Supply current I cc (see Note 2) Max. supply current I cc Max. supply current I cc Max. supply current I cc ...
Page 6
IHD 215/280/680 Data Sheet & Application Manual Electrical Characteristics (Continuation) Timing Characteristics Delay time input to output Delay time status output Outputs G1 and G2 Output current I out (see Note 8) Output rise time t r(out) (see Note 9) ...
Page 7
If the rising or falling times are too high (i.e. driving is too slow), reliable transfer of the drive informa- tion cannot be guaranteed. 8) The gate current must be limited to its maximum value by a gate resistor. ...
Page 8
IHD 215/280/680 Data Sheet & Application Manual components are required in the control circuit or in the power section. Reliable operation Gate driving with a positive and negative control voltage (depending on the selected supply voltage between 15V) allows reliable ...
Page 9
Layout of the terminals The terminal pins of the drive modules of the IHD series are arranged so that the layout can be kept very simple and the logic signal flow (input signal circuit power transistors) is maintained. A distance ...
Page 10
IHD 215/280/680 Data Sheet & Application Manual The leads IN1+ and IN1- must run in parallel and be well coupled (parallel tracks or twisted pairs). The minus leads must always be run back separately for both channels to the input ...
Page 11
... The maximum permissible charge/discharge current has a value of 1.5A for the IHD215 and 8A for both the IHD280 and the IHD680. This allows the largest IGBT and power MOSFET modules to be driven also possible to directly drive a number of power modules con- nected in parallel ...
Page 12
IHD 215/280/680 Data Sheet & Application Manual Fig. 5 Asymmetrical gate resistors It is mandatory to connect zener diodes (anti-series connected) directly between the gate and emitter for IGBTs. Their zener voltage must correspond exactly to the selected gate voltage ...
Page 13
Rme. Rme attenuates the reverse current peaks of the measurement diode Dme and should be set should be noted that the power ...
Page 14
IHD 215/280/680 Data Sheet & Application Manual The reference diode must be located as close as possible to the driver module. Pin 34 pin 23 Terminal Cs1 Cs2 Low-inductance blocking capacitors with high ripple current capability (electrolytic capacitors are usually ...
Page 15
Pin 35 pin 24 Terminal COM1 COM2 This is the ground terminal of the secon- dary-side blocking capacitor simulta- neously used as the reference potential for the measurement filter and the capacitors Cb1 Cb2 . In place of ...
Page 16
IHD 215/280/680 Data Sheet & Application Manual +15V Electronic GND Fig. 9 Correct input and output wiring Formulas for Circuit Calculations Response Time Capacitor ———————————— 1,5k ————— ...
Page 17
MC33151 high-side 18 17 220n low-side 4 3 +15V 250uF GND +15V GND 15 Status output 2 16 +15V 1 Status output 1 2 15k 15k GND GND Fig. 10 Application with a IHD680AI/AN: One phase ...
Page 18
IHD 215/280/680 Data Sheet & Application Manual In addition, CONCEPT offers ready designed and assembled three-phase bridges with IGBT modules. Additional documentation on these is available upon request. These boards can be used in conjunction with the documentation to build ...
Page 19
Fax Reply Form Please use a photocopier to enlarge to A4 size. Check elevant box [ the form and fax it to CONCEPT or to your local CONCEPT distribution partner! Please send us further information: Overview of all intelligent drivers ...
Page 20
IHD 215/280/680 Data Sheet & Application Manual Ordering Information Drivers for low power (2W converter, ±1,5A gate current) Standard version (0...70°C) Industry version (-40...+85°C) Drivers for medium power (2W converter, ±8A gate current) Standard version (0...70°C) Industry version (-40...+85°C) Drivers ...