LT6010 Linear Technology Corporation, LT6010 Datasheet
LT6010
Available stocks
Related parts for LT6010
LT6010 Summary of contents
Page 1
... A. The output voltage swings to within 40mV of either supply rail, making the amplifier a good choice for low voltage single supply operation. The LT6010 is fully specified at 5V and 15V supplies and from – The device is available in SO-8 and space-saving 3mm 3mm DFN packages. This op amp is also available in dual (LT6011) and quad (LT6012) packages ...
Page 2
... – LT6010ADD – LT6010DD – LT6010AS8, LT6010S8 LT6010ADD,LT6010DD ORDER PART TOP VIEW NUMBER 8 NULL LT6010CS8 + 7 V – LT6010IS8 + 6 OUT LT6010ACS8 SHDN 5 LT6010AIS8 S8 PACKAGE ...
Page 3
... T = – LT6010AS8 – LT6010S8 – LT6010ADD – LT6010DD – 0.1Hz to 10Hz f = 1kHz f = 1kHz Common Mode ...
Page 4
... – LT6010ADD – LT6010DD – LT6010AS8, LT6010S8 LT6010ADD,LT6010DD LT6010AS8 – LT6010S8 – LT6010ADD ...
Page 5
... – LT6010S8 – LT6010ADD – LT6010DD – 0.1Hz to 10Hz f = 1kHz f = 1kHz Common Mode 13.5V CM Differential Guaranteed by CMRR V = –13.5V to 13.5V CM Guaranteed by PSRR ...
Page 6
... Note 3: A heat sink may be required to keep the junction temperature below absolute maximum ratings. Note 4: Both the LT6010C and LT6010I are guaranteed functional over the operating temperature range of – Note 5: The LT6010C is guaranteed to meet the specified performance ...
Page 7
... G08 Output Saturation Voltage vs Load Current (Output High 5V 0 – 0.01 0.01 0.1 1 LOAD CURRENT (mA) 6010 G11 LT6010 Frequency 15V CURRENT NOISE 100 VOLTAGE NOISE 100 FREQUENCY (Hz) 6010 G06 0.01Hz to 1Hz Noise V ...
Page 8
... LT6010 W U TYPICAL PERFOR A CE CHARACTERISTICS Supply Current vs Supply Voltage 500 450 400 350 300 250 200 150 T = – 100 SUPPLY VOLTAGE ( V) 6010 G13 THD + Noise vs Frequency 15V 20V ...
Page 9
... 50pF L –5 –10 –15 –20 1k 10k 100k 1M FREQUENCY (Hz) 6010 G26 Large-Signal Transient Response 2V/DIV A = –1 50 s/DIV V 6011 G28 V = 15V S LT6010 Gain and Phase vs Frequency 5V 10k GAIN 20 PHASE 10 0 –10 – 20 –30 – 10k ...
Page 10
... For example resistor in series with each input provides protection against 30V differential voltage. Input Common Mode Range The LT6010 output is able to swing nearly to each power supply rail (rail-to-rail out), but the input stage is limited to operating between V common mode range will cause the gain to drop to zero, however no phase reversal will occur ...
Page 11
... U U APPLICATIO S I FOR ATIO Offset Voltage Adjustment The input offset voltage of the LT6010 and its drift with temperature are permanently trimmed at wafer testing to the low level as specified in the electrical characteristic. However, if further adjustment 50k potentiometer is possible and will not degrade drift with temperature ...
Page 12
... When pulled 2V or more above V drops to about 12 A, shutting down the op amp. The output of the LT6010 op amp is not isolated from the inputs while in shutdown mode. Therefore, this shutdown feature cannot be used for multiplexing applications. ...
Page 13
... Q7 Q3 BIAS CURRENT GENERATOR R1 500 2 –IN + 500 Q1 5 SHDN – NULL Q21 Q17 B A Q16 Q10 Q11 Q15 LT6010 R6 R5 Q18 Q13 Q12 Q14 Q9 Q10 Q19 6 OUT C3 Q20 6010 SS sn6010 6010fs 13 ...
Page 14
... LT6010 PACKAGE DESCRIPTIO 3.5 0.05 1.65 0.05 2.15 0.05 (2 SIDES) 0.28 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS PIN 1 TOP MARK 0.200 REF NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE 4. EXPOSED PAD SHALL BE SOLDER PLATED ...
Page 15
... TYP .016 – .050 .014 – .019 (0.406 – 1.270) (0.355 – 0.483) TYP INCHES (MILLIMETERS) LT6010 .189 – .197 (4.801 – 5.004) NOTE .150 – .157 (3.810 – 3.988) NOTE 3 1 ...
Page 16
... Rail-to-Rail Output, Picoamp Input Precision Op Amp Linear Technology Corporation 16 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 C4 C3 0.5pF 1pF + R3 V 100k – LT6010 LT6230 2.55k + – R2 – J1: PHILIPS BF862 C2 S1: SIEMENS/INFINEON SFH203 PHOTODIODE (~3pF) 0 SUPPLY 0. ...