AD9389 Analog Devices, AD9389 Datasheet - Page 20

• Manufacturer Part Number: AD9389
• Description: 800 MHz High Performance HDMI/DVI Transmitter
• Manufacturer: Analog Devices

www.DataSheet4U.com
AD9389
2-WIRE SERIAL REGISTER MAP
The AD9389 is initialized and controlled by a set of registers that determine the operating modes. An external controller is employed to
write and read the control registers through the two-line serial interface port.
Table 22. Control Register Map
Hex
Address
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
Read/Write or
Read Only
Read
Read/Write
Read/Write
Read/Write
Read
Read
Read
Read/Write
Read/Write
Read/Write
Read/Write
Bits
[7:0]
[3:0]
[7:0]
[7:0]
[7:4]
[3:0]
[7:0]
[7:0]
[3:0]
[7:0]
[7:0]
[7]
[6:5]
[4]
[3]
[2]
[1:0]
Default
Value
00000000
****0000
00000000
00000000
0000****
****0000
00000000
00000000
****0000
00000000
00000000
0*******
*10*****
***0****
****0***
*****0**
******01
Register Name
Chip Revision
N[19:16]
N[15:8]
N[7:0]
S/PDIF_SF
CTS_Int[19:16]
CTS_Int[15:8]
CTS_Int[7:0]
CTS_Ext[19:16]
CTS_Ext[15:8]
CTS_Ext[7:0]
CTS_Sel
Avg_Mode
Audio_Sel
MCLK_SP
MCLK_I
MCLK_Ratio
Rev. 0 | Page 20 of 48
2
S
Description
Revision of the chip, start from 0.
20-bit N used with cycle time stamp (CTS) (see Table
18 to Table 20 for appropriate settings) to regenerate
the audio clock in the receiver. For remaining bits, see
0x02 and 0x03. Used only with I
The middle byte of N.
The lower byte of N.
S/PDIF sampling frequency for S/PDIF audio decoded
from hardware. This information is used both by the
audio Rx and the pixel repetition.
0011 = 32 kHz.
0000 = 44.1 kHz.
0010 = 48 kHz.
1000 = 88.2 kHz.
1010 = 96 kHz.
1100 = 176.4 kHz.
1110 = 192 kHz.
Default = 0x0.
CTS measured (internal). This 20-bit value is used in
the receiver with the N value to regenerate an audio
clock. For remaining bits, see 0x05 and 0x06.
Middle byte of measured CTS.
Low byte of measured CTS.
CTS (external). This 20-bit value is used in the receiver
with the N value to regenerate an audio clock. For
remaining bits, see 0x08 and 0x09.
Middle byte of external CTS.
Low byte of external CTS.
CTS source select.
0 = internal CTS.
1 = external CTS.
Default = 0.
CTS filter mode.
00 = no filter.
01 = divide by 4.
10 = divide by 8.
11 = divide by16.
Default = 10.
Audio type select.
0 = I
1 = S/PDIF.
Default = 0.
MCLK for S/PDIF.
1 = MCLK active.
0 = MCLK inactive.
Default = 0.
MCLK for I
1 = I
0 = I
Default = 0.
MCLK ratio.
2
2
2
S.
S MCLK active.
S MCLK inactive.
2
S.
2
S audio, not S/PDIF.