MAX1304 Maxim, MAX1304 Datasheet - Page 24
![no-image](/images/no-image-200.jpg)
MAX1304
Manufacturer Part Number
MAX1304
Description
8-/4-/2-Channel / 12-Bit / Simultaneous-Sampling ADCs with 10V / 5V / and 0 to +5V Analog Input Ranges
Manufacturer
Maxim
Datasheet
1.MAX1304.pdf
(36 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX13041ASD
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX13041ASD+
Manufacturer:
Maxim
Quantity:
40
Company:
Part Number:
MAX13041ASD+T
Manufacturer:
MAXIM
Quantity:
33
Company:
Part Number:
MAX13047EEVB+T
Manufacturer:
ZARLNK
Quantity:
201
Part Number:
MAX13047EEVB+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX13047EEVKIT+
Manufacturer:
Maxim Integrated Products
Quantity:
135
Company:
Part Number:
MAX1304ECM+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
MAX1304ECM+T
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
MAX1304ECM/V+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
MAX1304ECM/V+T
Manufacturer:
Maxim Integrated
Quantity:
10 000
At power-up, all channels are selected for conversion
(see the Configuration Register section). After applying
power, allow the 1ms wake-up time to elapse and then
initiate a dummy conversion and discard the results.
After the dummy conversion is complete, accurate con-
versions can be obtained.
During shutdown the internal reference and analog
circuits in the device shutdown and the analog supply
current drops to 0.6µA (typ). Select shutdown mode
using the SHDN input. Set SHDN high to enter shut-
down mode. SHDN takes precedence over CHSHDN.
Entering and exiting shutdown mode does not change
the configuration byte. However, a new configuration
byte can be written while in shutdown mode by follow-
ing the standard write procedure shown in Figure 6.
EOC and EOLC are high when the MAX1304–MAX1306/
MAX1308–MAX1310/MAX1312–MAX1314 are shut down.
The state of the digital outputs D0–D11 is independent
of the state of SHDN. If CS and RD are low, the digital
outputs D0–D11 are active regardless of SHDN. The
digital outputs only go high impedance when CS or RD
is high. When the digital outputs are powered down, the
digital supply current drops to 20nA.
8-/4-/2-Channel, 12-Bit, Simultaneous-Sampling ADCs
with ±10V, ±5V, and 0 to +5V Analog Input Ranges
Figure 9. Read After Conversion—Eight Channels Selected, External Clock
24
CONVST
D0–D11
EOLC
______________________________________________________________________________________
EOC
CS*
RD
* CS CAN BE LOW AT ALL TIMES, LOW DURING THE RD CYCLES, OR THE SAME AS RD.
ONLY LAST PULSE SHOWN
Power-Saving Modes
t
CTR
Power-Up Reset
t
EOC
t
ACC
Shutdown Mode
CH0
t
REQ
t
RDL
CH1
CH2
Exiting shutdown (falling edge of SHDN) starts a con-
version in the same way as the rising edge of CONVST.
After coming out of shutdown, initiate a dummy conver-
sion and discard the results. After the dummy conver-
sion, allow the 1ms wake-up time to expire before
initiating the first accurate conversion.
The channel-shutdown feature allows analog input
channels to be powered down when they are not
selected for conversion. Powering down channels that
are not selected for conversion reduces the analog
supply current by 2.9mA per channel. To power down
channels that are not selected for conversion, pull
CHSHDN low. See the Configuration Register section
for information on selecting and deselecting channels
for conversion.
The drawback of powering down analog inputs that are
not selected for conversion is that it takes time to power
them up. Figure 10 shows how a dummy conversion is
used to power up an analog input in external clock
mode. After selecting a new channel in the configura-
tion register, initiate a dummy conversion and discard
the results. After the dummy conversion, allow the 1ms
wake-up time (t
accurate conversion.
CH3
t
RDH
WAKE
CH4
) to expire before initiating the first
CH5
Channel Shutdown
t
QUIET1
CH6
= 50ns
t
t
RTC
CVEOLCD
CH7
(C C H H S S H H D D N N )