ATA8741 ATMEL Corporation, ATA8741 Datasheet - Page 192

• Manufacturer Part Number: ATA8741
• Manufacturer: ATMEL Corporation

Table 28-15. High-voltage Serial Programming Instruction Set for ATtiny24/44/84
192
Instruction
Chip Erase
Load “Write
Flash”
Command
Load Flash
Page Buffer
Load Flash
High Address
and Program
Page
Load “Read
Flash”
Command
Read Flash
Low and High
Bytes
Load “Write
EEPROM”
Command
Load
EEPROM
Page Buffer
Program
EEPROM
Page
ATA8741
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
0_1000_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0001_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_ bbbb_bbbb _00
0_0000_1100_00
x_xxxx_xxxx_xx
0_dddd_dddd_00
0_0011_1100_00
x_xxxx_xxxx_xx
0_0000_000a_00
0_0001_1100_00
x_xxxx_xxxx_xx
0_0000_0010_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_bbbb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1000_00
x_xxxx_xxxx_xx
0_0001_0001_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_bbbb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
Instr.1/5
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_eeee_eeee_00
0_0010_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1101_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_0000_000a_00
0_0001_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
p_pppp_pppx_xx
0_aaaa_aaaa_00
0_0001_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
Instr.2/6
Instruction Format
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1101_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1000_00
x_xxxx_xxxx_xx
0_eeee_eeee_00
0_0010_1100_00
x_xxxx_xxxx_xx
Instr.3/7
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
q_qqqq_qqqx_xx
0_0000_0000_00
0_0110_1101_00
x_xxxx_xxxx_xx
Instr.4
Operation Remarks
Wait after Instr.3 until SDO
goes high for the Chip Erase
cycle to finish.
Enter Flash Programming code.
Repeat after Instr. 1 - 7until the
entire page buffer is filled or
until all data within the page is
filled. See Note 1.
Wait after Instr 3 until SDO
goes high. Repeat Instr. 2 - 3
for each loaded Flash Page
until the entire Flash or all data
is programmed. Repeat Instr. 1
for a new 256 byte page. See
Note 1.
Enter Flash Read mode.
Repeat Instr. 1, 3 - 6 for each
new address. Repeat Instr. 2 for
a new 256 byte page.
Instr 5 - 6.
Enter EEPROM Programming
mode.
Repeat Instr. 1 - 5 until the
entire page buffer is filled or
until all data within the page is
filled. See Note 2.
Wait after Instr. 2 until SDO
goes high. Repeat Instr. 1 - 2
for each loaded EEPROM page
until the entire EEPROM or all
data is programmed.
Instr 5-7.
9140B–INDCO–07/09