MAX17036 Maxim Integrated Products, MAX17036 Datasheet - Page 2

• Manufacturer Part Number: MAX17036
• Description: (MAX17030 / MAX17036) 1/2/3-Phase Quick-PWM IMVP-6.5 VID Controllers
• Manufacturer: Maxim Integrated Products

www.DataSheet4U.com
1/2/3-Phase Quick-PWM
IMVP-6.5 VID Controllers
ABSOLUTE MAXIMUM RATINGS
(Note 1)
V
D0–D6, PGD_IN, PSI, DPRSLPVR to GND ...............-0.3V to +6V
CSP_, CSN_, THRM, ILIM to GND............................-0.3V to +6V
PWRGD, CLKEN, VR_HOT to GND..........................-0.3V to +6V
FB, FBAC, IMON, TIME to GND .................-0.3V to (V
SHDN to GND (Note 2)...........................................-0.3V to +30V
TON to GND ...........................................................-0.3V to +30V
GNDS to GND .......................................................-0.3V to +0.3V
DL1, DL2, PWM3, DRSKP to GND .............-0.3V to (V
BST1, BST2 to GND ...............................................-0.3V to +36V
BST1, BST2 to V
ELECTRICAL CHARACTERISTICS
(Circuit of Figure 1, V
1.0000V, FB = FBAC, R
Typical values are at T
Note 1: Absolute Maximum Ratings valid using 20MHz bandwidth limit.
Note 2: SHDN might be forced to 12V for the purpose of debugging prototype breadboards using the no-fault test mode. Internal
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2
PWM CONTROLLER
Input Voltage Range
FB Output Voltage Accuracy
Boot Voltage
Line Regulation Error
FB Input Bias Current
GNDS Input Range
GNDS Gain
GNDS Input Bias Current
TIME Regulation Voltage
TIME Slew-Rate Accuracy
CC
, V
_______________________________________________________________________________________
DD
BST switches are disabled as well. Use external BST diodes when SHDN is forced to 12V.
to GND .....................................................-0.3V to +6V
PARAMETER
DD
.................................................-0.3V to +30V
IN
A
= +25°C.)
= 10V, V
FBAC
= 3.57kΩ from FBAC to CSN_, [D6–D0] = [0101000]; T
CC
SYMBOL
= V
A
V
I
V
GNDS
BOOT
GNDS
V
TIME
DD
FB
= V
SHDN
V
V
Measured at FB
with respect to
GNDS;
includes load-
regulation error
(Note 3)
V
T
T
R
R
R
178k
Soft-start and soft-shutdown:
R
178k
A
A
CC
IN
CC
V
TIME
TIME
TIME
TIME
OUT
CC
DD
= +25°C
= +25°C
, V
= 4.5V to 5.5V, V
= V
DD
+ 0.3V)
+ 0.3V)
/ V
= 147k
= 147k
= 35.7k
= 35.7k
(5mV/µs nominal)
(1.25mV/µs nominal)
PGD_IN
GNDS
CONDITIONS
(6.08mV/µs nominal)
= V
(25mV/µs nominal) to
(6.25mV/µs nominal) to
LX1 to BST1..............................................................-6V to +0.3V
LX2 to BST2..............................................................-6V to +0.3V
DH1 to LX1 ..............................................-0.3V to (V
DH2 to LX2 ..............................................-0.3V to (V
Continuous Power Dissipation (40-pin, 5mm x 5mm TQFN)
Operating Temperature Range .........................-40°C to +105°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +165°C
Lead Temperature (soldering, 10s) .................................+300°C
PSI
DAC codes from
0.8125V to 1.5000V
DAC codes from
0.3750V to 0.8000V
DAC codes from
0 to 0.3625V
IN
Up to +70°C ..............................................................1778mW
Derating above +70°C ..........................................22.2mW/°C
= 4.5V to 26V
= V
ILIM
= 5V, V
A
DPRSLPVR
= 0°C to +85°C, unless otherwise noted.
1.094
1.985
-200
0.97
MIN
-0.5
-0.1
-0.5
4.5
-20
-10
-15
-20
-7
7
= V
GNDS
1.100
2.000
TYP
1.00
0.1
= 0, V
1.106
2.015
+200
MAX
+0.5
+0.1
+0.5
1.03
+20
+10
+15
+20
5.5
+7
CSP_
26
BST1
BST2
= V
UNITS
+ 0.3V)
+ 0.3V)
CSN_
V/V
mV
mV
µA
µA
%
%
%
V
V
V
=