CM12RA02 Taiyo Yuden Co., Ltd, CM12RA02 Datasheet - Page 9

• Manufacturer Part Number: CM12RA02
• Description: Common Mode Choke Coils For Dc And Signal Lines Leaded Type
• Manufacturer: Taiyo Yuden Co., Ltd

co0304_reli-RP5
■
CM-RA Type, CM-RB Type, TLF Type
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
Precautions
Precautions
Precautions
Precautions
Precautions
Precautions
1. Circuit Design
2. PCB Design
3. Soldering
4. Cleaning
5. Handling
6. Storage conditions
Technical
consider-
Technical
consider-
Technical
consider-
Technical
consider-
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
PRECAUTIONS
ations
ations
ations
ations
◆Operating environment
◆Design
◆Design
◆Wave soldering
◆Lead free soldering
◆Recommended conditions for using a soldering iron
◆Lead free soldering
◆Cleaning conditions
◆Handling
◆Mechanical considerations
◆Packing
◆Handling
◆Mechanical considerations
◆Packing
◆Storage
◆Storage
1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems,
1. Please design insertion pitches of a base in the pitches that fitted a terminal interval.
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire Inductors in the flux during the soldering operation.
1. When using products with lead free soldering, we request to use them after confirming of adhesion, temperature of resistance to soldering heat, etc.
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
1. TLF type
1. Keep the product away from all magnets and magnetic objects.
1. Please do not give the product any excessive mechanical shocks.
2. TLF type
1. Please do not give the product any excessive mechanical shocks.
1. There is a case that a characteristic varies with magnetic influence.
1. There is a case to be damaged by a mechanical shock.
2. TLF type
1. There is a case that a lead route turns at by a fall or an excessive shock.
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
・ Put the soldering iron on the land-pattern.
・ Soldering iron's temperature - Below 350℃
・ Duration - 3 seconds or less
・ The soldering iron should not directly touch the product.
・ Recommended conditions
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
sufficiently.
the products.
be controlled.
taping/packaging materials may take place.
Please contact any of our offices for about a cleaning.
Please do not add any shock or and power to a product in transportation.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item).
There is a case to be broken by a fall.
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, product should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Ambient temperature : 0∼40℃
Humidity
: Below 70% RH
1
co0304_reli_e-01