MT8976 Mitel Networks Corporation, MT8976 Datasheet - Page 13

• Manufacturer Part Number: MT8976
• Description: ISO-CMOS ST-BUS FAMILY T1/ESF Framer Circuit
• Manufacturer: Mitel Networks Corporation

Received Signalling Bits
The A, B, C and D signalling bits are output from the
device in the 24 Per Channel Status Words. Their
location in the serial steam output at CSTo is shown
in Figure 6 and the bit positions are shown in Table
11. The internal debouncing of the signalling bits can
be turned on or off by Master Control Word 1. In ESF
mode, A, B, C and D bits are valid. Even though the
signalling bits are only received once every six
frames the device stores the information so that it is
available on the ST-BUS every frame. The ST-BUS
will always contain the most recent signalling bits.
The state of the signalling bits is frozen if
synchronization is lost.
In D3/D4 mode, only the A and B bits are valid. The
state of the signalling bits is frozen when terminal
frame synchronization is lost. The freeze is disabled
when
synchronization. The signalling bits may go through a
random transition stage until the device attains
multiframe synchronization.
Clock and Framing Signals
The MT8976 requires one 2.048 MHz clock (C2i) and
an 8 kHz framing signal for the ST-BUS side. Figure
12 illustrates the relationship between the two
signals. The framing signal is used to delimit
individual 32 channel ST-BUS frames.
The DS1 side requires two clocks. A 1.544 MHz
clock used for transmit (C1.5i), and a 1.544 MHz
clock extracted from the DS1 line signal and applied
at E1.5i pin to clock in the received data.
The C2i and C1.5i clock must be phase-locked
together. There must be 193 clock cycles of C1.5i for
every 256 clock cycles of C2i. At the slave end of the
link, the C2i and C1.5i must be phase locked to the
extracted E1.5i clock.
The clock applied at E1.5i is internally divided down
by 193 and aligned with the DS1 frame. The resulting
8 kHz clock is output at the E8Ko pin. This signal
can be used as a reference for phase locking the C2i
and C1.5i clocks to the extracted 1.544 MHz clock.
DS1 Line Interface
Transmit Interface
The interface to the DS1 line is made up of two
unipolar outputs, TxA and TxB, which can be used to
drive a bipolar transmitter circuit. The output signal
the
device
regains
terminal
frame
on TxA and TxB corresponds to the positive and
negative bipolar pulses required for the Alternate
Mark Inversion signal on the T1 line. The relationship
between the signal output at TxA and TxB and the
AMI signal is illustrated in Figure 5. For transmission
over twisted pair wire, the AMI signal has to be
equalized and transformer coupled to the line.
Receiver Interface
The receiver circuitry is made up of three pins RxA,
RxB and RxD. The bipolar alternate mark inversion
signal from the DS-1 line should be converted into a
unipolar split phase format. The resulting signals
are clocked into the device at RxA and RxB. The
signals are also NANDED together and input at RxD.
In special applications where the detection of bipolar
violations is not required, it is possible to clock NRZ
data directly into RxD. In this case, the RxA and
RxB pins should be tied high.
Data is clocked into RxA,
falling edge of the E1.5i clock. This clock signal is
extracted from the received data. The relationship
between the received signals and the extracted clock
is shown in Figure 4.
Elastic Buffer
The MT8976 has a two frame elastic buffer which
absorbs jitter in the received DS1 signal. The buffer
is also used in the rate conversion between the 1.544
Mbit/s DS1 rate and the 2.048 Mbit/s ST-BUS data
rate.
The received data is written into the elastic buffer
with the extracted 1.544 MHz clock. The data is read
out of the buffer on the ST-BUS side with the system
2.048 MHz clock. The maximum delay through the
buffer is 1.3 ST-BUS frames (i.e., 42 ST-BUS
channels). The minimum delay required to avoid bus
contention in the buffer memory is two ST-BUS
channels.
Under normal operating conditions, the system C2i
clock is phase locked to the extracted E1.5i clock
using external circuitry. If the two clocks are not
phase-locked, then the rate at which the data is
being written into the device on the DS1 side may
differ from the rate at which it is being read out on the
ST-BUS side. The buffer circuit will perform a
controlled slip if the throughput delay conditions
described above are violated. For example, if the
data on the DS1 side is being written in at a rate
slower than what it is being read out on the ST-BUS
side, the delay between the received DS1 write
ISO-CMOS
RxB and RxD with the
MT8976
4-41