M1MA152WA Motorola Inc, M1MA152WA Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
M1MA152WA
Manufacturer Part Number
M1MA152WA
Description
Common Anode Silicon Dual Switching Diodes
Manufacturer
Motorola Inc
Datasheet
1.M1MA152WA.pdf
(6 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M1MA152WA
Manufacturer:
ON
Quantity:
54 000
Company:
Part Number:
M1MA152WAT1G
Manufacturer:
ON Semiconductor
Quantity:
19 200
Company:
Part Number:
M1MA152WAT1G
Manufacturer:
ON
Quantity:
30 000
Part Number:
M1MA152WAT1G
Manufacturer:
ON/安森美
Quantity:
20 000
M1MA151WAT1 M1MA152WAT1
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a
figure for belt speed. Taken together, these control settings
make up a heating “profile” for that particular circuit board.
On machines controlled by a computer, the computer
remembers these profiles from one operating session to the
next. Figure 1 shows a typical heating profile for use when
soldering a surface mount device to a printed circuit board.
This profile will vary among soldering systems but it is a good
starting point. Factors that can affect the profile include the
type of soldering system in use, density and types of
components on the board, type of solder used, and the type
of board or substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
4
Prior to placing surface mount components onto a printed
For any given circuit board, there will be a group of control
150 C
100 C
200 C
50 C
PREHEAT
ZONE 1
“RAMP”
STEP 1
TIME (3 TO 7 MINUTES TOTAL)
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
TYPICAL SOLDER HEATING PROFILE
150 C
Figure 1. Typical Solder Heating Profile
STEP 2
“SOAK”
VENT
SOLDER STENCIL GUIDELINES
100 C
ZONES 2 & 5
DESIRED CURVE FOR LOW
HEATING
“RAMP”
STEP 3
MASS ASSEMBLIES
Motorola Small–Signal Transistors, FETs and Diodes Device Data
160 C
ZONES 3 & 6
140 C
HEATING
STEP 4
“SOAK”
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the SC–59 package should be
the same as the pad size on the printed circuit board, i.e., a
1:1 registration.
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density board.
The Vitronics SMD310 convection/infrared reflow soldering
system was used to generate this profile. The type of solder
used was 62/36/2 Tin Lead Silver with a melting point
between 177 –189 C. When this type of furnace is used for
solder reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
SOLDER IS LIQUID FOR
MASS OF ASSEMBLY)
40 TO 80 SECONDS
ZONES 4 & 7
170 C
(DEPENDING ON
HEATING
“SPIKE”
STEP 5
T MAX
STEP 6
VENT
SOLDER JOINT
205 TO 219 C
COOLING
STEP 7
PEAK AT