ISL6140 Intersil Corporation, ISL6140 Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
ISL6140
Manufacturer Part Number
ISL6140
Description
Negative Voltage Hot Plug Controller
Manufacturer
Intersil Corporation
Datasheet
1.ISL6140.pdf
(17 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL6140CBZ
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6140CBZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL6140IB
Manufacturer:
HARRIS
Quantity:
5 536
Part Number:
ISL6140IBZ
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL6140IBZ-T
Manufacturer:
Intersil
Quantity:
4
Company:
Part Number:
ISL6140IBZ-T
Manufacturer:
Intersil
Quantity:
14 000
Q1 - is the FET that connects the input supply voltage to the
output load, when properly enabled. It needs to be selected
based on several criteria: maximum voltage expected on the
input supply (including transients) as well as transients on
the output side; maximum current expected; power
dissipation and/or safe-operating-area considerations (due
to the quick over-current latch, power dissipation is usually
not a problem compared to systems where current limiting is
used; however, worst case power is usually at a level just
below the overcurrent shutdown). Other considerations
include the gate voltage threshold which affects the Rdson
(which in turn, affects the voltage drop across the FET
during normal operation), and the maximum gate voltage
allowed (the IC clamp output is clamped to ~14V).
R1 - is the Over-Current sense resistor; if the input current is
high enough, such that the voltage drop across R1 exceeds
the SENSE comparator trip point (50mV nominal), the GATE
pin will go low, turning off the FET, to protect the load from
the excessive current. A typical value for R1 is 0.02Ω; this
sets an Over-Current trip point of I = V/R = 0.05/0.02 = 2.5A.
So, to choose R1, the user must first determine at what level
of current it should trip. Take into account worst case
variations for the trip point (50mV ±10mV = ±20%), and the
R1 resistance (typically 1% or 5%). Note that under normal
conditions, there will be a voltage drop across the resistor (V
= IR), so the higher the resistor value, the bigger the voltage
drop. Also note that the Over-Current should be set above
the inrush current level (plus the load current); otherwise, it
will latch off during that time (the alternative is to lower the
inrush current further). One rule of thumb is to set the Over-
Current 2-3 times higher than the normal current.
R1 = V / I
CL - is the sum of all load capacitances, including the load’s
input capacitance itself. Its value is usually determined by
the needs of the load circuitry, and not the hot plug (although
there can be interaction). For example, if the load is a
regulator, then the capacitance may be chosen based on the
input requirements of that circuit (holding regulation under
current spikes or loading, filtering noise, etc.) The value
chosen will then affect how the inrush current is controlled.
Note that in the case of a regulator, there may be capacitors
on the output of that circuit as well; these need to be added
into the capacitance calculation during inrush (unless the
regulator is delayed from operation by the PWRGD signal,
for example).
RL - is the equivalent resistive value of the load; it
determines the normal operation current delivered through
the FET. It also affects some dynamic conditions (such as
the discharge time of the load capacitors during a power-
down). A typical value might be 48Ω (I=V/R = 48/48 = 1A).
R2, C1, R3, C2 - are related to the gate driver, as it controls
the inrush current.
oc
= 0.05V / I
oc
(typical = 0.02Ω)
7
ISL6140, ISL6150
R2 prevents high frequency oscillations; 10Ω is a typical
value. R2 = 10Ω.
R3 and C2 act as a feedback network to control the inrush
current. I inrush = (Igate * CL)/C2, where CL is the load
capacitance (including module input capacitance), and Igate
is the gate pin charging current, nominally 45µA. So choose
a value of acceptable inrush for the system, and then solve
for C2. So I = 45µA * (CL/C2). Or C2 = (45µA * CL)/I.
C1 and R3 prevent Q1 from turning on momentarily when
power is first applied. Without them, C2 would pull the gate
of Q1 up to a voltage roughly equal to VEE*C2/Cgs(Q1)
(where Cgs is the FET gate-source capacitance) before the
ISL6140 could power up and actively pull the gate low. Place
C1 in parallel with the gate capacitance of Q1; isolate them
from C2 by R3.
C1 = (Vinmax - Vth)/Vth * (C2+Cgd) - where Vth is the
FET’s minimum gate threshold, Vinmax is the maximum
operating input voltage, and Cgd is the FET gate-drain
capacitance.
R3 = (Vinmax + deltaVgate)/5mA - its value is not critical; a
typical value is 18kΩ.
Applications: Inrush Current
The primary function of the ISL6140 hot plug controller is to
control the inrush current. When a board is plugged into a
live backplane, the input capacitors of the board’s power
supply circuit can produce large current transients as they
charge up. This can cause glitches on the system power
supply (which can affect other boards!), as well as possibly
cause some permanent damage to the power supply.
The key to allowing boards to be inserted into a live
backplane then is to turn on the power to the board in a
controlled manner, usually by limiting the current allowed to
flow through a FET switch, until the input capacitors are fully
charged. At that point, the FET is fully on, for the smallest
voltage drop across it.
In addition to controlling the inrush current, the ISL6140 also
protects the board against over-current, over-voltage, under-
voltage, and can signal when the output voltage is within its
expected range (PWRGD).
Note that although this IC was designed for -48V systems, it
can also be used as a low-side switch for positive 48V
systems; the operation and components are usually similar.
One possible difference is the kind of level shifting that may
be needed to interface logic signals to the UV input (to reset
the latch) or PWRGD output. For example, many of the IC
functions are referenced to the IC substrate, connected to
the VEE pin. But this pin may be considered -48V or GND,
depending upon the polarity of the system. And input or
output logic (running at 5V or 3.3V or even lower) might be
externally referenced to either VDD or VEE of the IC, instead
of GND.